background image

RFL Auxiliary Hybrid Chassis 

 

RFL Electronics Inc. 

March 29, 2005 

                         1 

(973) 334-3100 

 
 
 
 

RFL Electronics Inc. 

 

 

I N S T R U C T I O N   D A T A 

 
 

RFL 9780/9785 

Auxiliary Hybrid Chassis 

 

 
 
 
 
 
 
 
 
 
 

 
 

 
 
 

 

Figure 1. RFL 9780/85 Auxiliary Hybrid Chassis, front view 
 
 
 

DESCRIPTION 

 

Hybrids are optional modules for the RFL Powerline Carrier equipment. They may be used to combine 
combinations of transmitters and receivers to a single port for connection to line tuning units. There is 
an X-Hybrid Module and a Skewed Hybrid Module available.  Each of these modules uses the same 
basic printed circuit board.  

 

The Auxiliary Hybrid Chassis shown in Figure 1 is used to add X-Hybrid modules or Skewed Hybrid 
modules to RFL Powerline Carrier systems. Each Auxiliary Hybrid is contained in a 19-inch chassis 
that occupies less than one rack unit of vertical rack space (1.718 inches, or 4.4 cm). Each chassis can 
accommodate three Hybrid modules and three Hybrid I/O modules. The Hybrid modules are mounted 
in the front of the chassis, and the Hybrid I/O modules are mounted at the rear of the chassis. In a 
given chassis the Hybrid modules can be a mix of any combination of  X-Hybrid modules or Skewed 
Hybrid modules. 

AUXILIARY HYBRID CHASSIS 

 

RFL Electronics Inc. 

Summary of Contents for 106630-1

















Reviews: