background image

Assembly and

operating instructions

Spare Tire Carrier

part number 195125, U.S. patent 8,720,760

ROADMASTER, Inc.    6110 NE 127th Ave.    Vancouver, WA 98682    800-669-9690    Fax: 360-735-9300    www.roadmasterinc.com

All specifications are subject to change without notice.

Time Tested  •  Time Proven

                                                                                                                               

855712-00   08-18

Figure 1

  Read all instructions before assem-
bling or operating this device. Failure to 
understand how to properly assemble 
or operate the spare tire carrier could 
result in extensive property damage or 
severe personal injury.

  Do not use a hitch extension, a high-low hitch or 
any similar product in conjunction with the spare tire 
carrier, or failure of any of these components may 
occur resulting in property damage, personal injury 
or even death.

Assembly instructions

Tools required

•  torque wrench
•  Socket wrenches in the following sizes: ¾"; 15/16"; and 
1-1/8"

 

1.

  Slide the main receiver hitch (Figure 1) into the mo-

torhome hitch receiver until the pre-drilled hitch receiver 
bolt hole aligns to the corresponding hole in the hitch 
receiver.
 

2.

  Use a 15/16" socket wrench to attach the 3½" hitch 

receiver  mounting bolt (Figure 1), with the lock washer 
under the bolt head. Torque to 100 ft./lbs. Secure it with 
the provided hairpin clip or with an optional padlock, 
ROADMASTER part number 301.

   Note: although not required, we recommend using 

continued on next page

  WARNING indicates a potentially hazardous situation 
which, if not avoided, could result in property damage, 
serious personal injury or even death.

  CAUTION indicates a potentially hazardous situation 
which, if not avoided, may result in property damage, 
or minor or moderate personal injury.

Safety Definitions

  These instructions contain information that is very important to know and understand. This information is provided for 

safety

 and to 

prevent equipment problems

. To help recognize this information, observe the following symbols:

CAUTION

  CAUTION used without the safety alert symbol in-
dicates a potentially hazardous situation which, if not 
avoided, may result in property damage. 

NOTE

  Refers to important information and is placed in italic type. 
It is recommended that you take special notice of these 
items.

Summary of Contents for 195125

Page 1: ... aligns to the corresponding hole in the hitch receiver 2 Use a 15 16 socket wrench to attach the 3 hitch receiver mounting bolt Figure 1 with the lock washer under the bolt head Torque to 100 ft lbs Secure it with the provided hairpin clip or with an optional padlock ROADMASTER part number 301 Note although not required we recommend using continued on next page WARNING indicates a potentially haz...

Page 2: ... Holding the lever swing the spare tire carrier to the ground Be careful when lowering the spare tire carrier Property damage or severe personal injury can result if it is allowed to fall 2 Roll the spare tire up to the spare tire carrier Position the wheel so that a lug hole is at the top aligned to the upper and lower holes Figure 3 3 If the wheel has a smaller bolt circle see the Fit Chart in F...

Page 3: ...ceiver hitch can be used to attach the safety cables Maintenance 1 At the beginning of each towing season check to ensure that all fasteners are tight Using the spare tire carrier will decrease the weight capacity of the vehicle s hitch receiver by one third This lowered capacity must still be more than the weight of a towed vehicle or hitch accessory attached to the spare tire carrier If it is no...

Page 4: ... lock washer 9 1 350314 20 SAE washer 10 2 350358 00 acetal washer 11 2 350372 60 9 16 x 2 x 0 063 nylon washer 12 1 350734 00 5 8 lock washer yellow zinc 13 1 357000 50 linch pin 14 1 357036 00 3 16 R clip 15 1 357395 58 5 8 external snap ring 16 1 A 004924 12 gauge flat washer 17 1 A 005102 5 8 11 x 3 grade 8 bolt 18 1 A 005363 lever 19 1 B 002718 5 8 lock pin 20 1 C 002956 safety bolt 21 1 C 00...

Reviews: