background image

 

 

FT0835 

Professional Wireless Weather Station 

User Manual 

 

1.Introduction 

Thank you for your purchase of the FT0835 

Professional Wireless Weather station

. The 

following user guide provides step by step instructions for installation, operation and 
troubleshooting. 

2.Warnings 

Warning: 

Any metal object may attract a lightning strike, including your weather 

station mounting pole. Never install the weather station in a storm.  

Warning: 

Installing your weather station in an elevated location may result in injury or 

death. Safety goes first. Make sure your setup and preparation is secure, and take no risks. 

3.Getting Started 

The FT0835 weather station consists of a display console (receiver),  a sensor array with 
Integrated Outdoor Transmitter and mounting hardware 
 

3.1.Parts List 

The FT0835 weather station consists of the following parts (as referenced in Figure 1 ).  

QTY

 

Item

 

Image

 

Display Console

 

Frame Dimensions (LxHxW): 
135X26X96mm 
LCD Dimensions (LxW): 111 x 75mm 

 

Integrated Outdoor Transmitter 

Dimensions (LxHxW)

330x150x280mm 

 

Summary of Contents for FT0835

























Reviews: