Warning
BIOMETRICS
Outer Body
SHP-DP728
64&3."/6"-
www.samsungsds-nss.com/en
GC68-02163A ED:02
Convenient Opening
Easy push/pull handle access
Welcome Function
When a user gets close to the door lock,
the authorization standby mode will
automatically activate.
Silent-Mode Function
When going in or out, the sound of the
key entering and door opening will be
suspended.
Automatic Card Reading Function
When a card touches the reader,
the reader will conveniently recognize the card.
Double Authorization
Requires password & fingerprint combination to open
Security Assurance Function
When someone is inside the house,
authorization for entry from the outside
will be prohibited.
Built-in Fire Detection
Generates alarm in case of a fire
Security Function
Prevents intrusion from the outside
BIOMETRICS
Smartphone Interworking function
G
Conveniently open the door through the Bluetooth
function of a smart phone
2
3
4
5
6
Inner Body
Mortise
Strike
(For B2C Only)
Strike box
Key Tag (For B2C Only) (2EA)
User Manual, Product Warranty
‘AA’ Batteries (LR6)
Emergency Key
Handle Shaft Spring
Handle Shaft, Installation Screws
Installation Manual(For B2C Only)
BIOMETRICS
BIOMETRICS
BIOMETRICS
CARD
BIOMETRICS
CARD
BIOMETRICS
CARD
When purchased, the product is set to Multi-leveled Security Code Entry Mode
initially. Please refer to “Multi-leveled Security Code Entry Mode setting” for Com-
mon Mode setting.
※
Silent Mode
Before entering the password, press the [
] button and enter the password, then both
the sound of the key entering and the door opening will be suspended. It is a useful
function if you do not want to disturb neighbors when you go in and out at night.
BIOMETRICS
BIOMETRICS
Mortise
(SHS-AML320)
Strike
box
Strike
Mortise
(SHS-AML220)
Strike
CARD
CARD
Safety Cautions
This section contains important information to ensure the user’s safety
and prevent potential damage to property. Please, read this section
carefully and use the product accordingly.
• The user shall not install or repair the
product without authorization.
• Do not install the product in the place
where the gap between the door and the
frame is 5mm or more.
• Make sure that no unauthorized person
has the access to the password.
• Do not operate the product with wet
hands, and keep liquids such as water
or drinks away from the product, or the
product may malfunction or be damaged.
• Do not use the excessive force or sharp
objects to push the lockbuttons, as this
can damage the product.
• Make sure that the door is completely
closed when going outside. The
manufacturer does not assume the
responsibility for any harm caused by
engagement of the lock on an improperly
closed door.
• Please do not hang on the product or pull it.
• Long-term exposure to direct sunlight
may cause a crack on its touch pad.
Avoid exposure to direct sunlight during
installation.
• During battery replacement, use a new one
instead of the existing battery.
• Be sure to correctly match the poles (+/-)
when installing the batteries. Install the
batteries with the correct poles (+/-).
• Do not use water, benzene or alcohol when
cleaning the product, as these fluids can
cause product malfunction.
• Replace the batteries within 1 week after
the battery replacement alarm sounds.
• Interference in wireless communication may
occur when this product is used.
• According to the wireless communication
environment, its battery may consume
much.
Product Components
The product components used may vary depending on the installation
environment.
Outer Body Parts
Number Pad
Unlighted
Touch Number Pad
Number Pad Lighted
Fingerprint
Reading Panel
Open Fingerprint
Cover Button
Card Reader
Proximity Sensor
Number Pad
Away Security
Setup
Emergency Alert
Light
Double Lock Light
External Power
Contact Part
Reset Switch
Emergency
Keyhole
Entry Complete/
Silent Mode
Switch Button
Battery
Replacement
Time Alert
Inner Body Parts
Mortise
1.5V AA Batteries
Sound Control Switch
Built-in Wireless Module (Optional)
Auto/Manual
Locking Switch
Battery Cover
Registration
Button
CLOSE Button
The Battery Cover Release
Button
(After pressing the battery cover
release button, pull towards the
front, and then the battery cover
will open.)
Deadbolt
Latch bolt
Open-door sensor
SHS-AML320
SHS-AML220
Opening the Door from Outside with a Password
Multi-leveled Security Code Entry Mode
Touching [Number
Pad] will light up
the number pad.
When two arbitrary but-
tons are lighted, press
the buttons in order.
When the numbers on the number
pad are lighted, enter the password
and press the [
] button.
Success:
DING DONG DENG DONG
Fail:
DING DONG DING DONG
Note
●
Password must be entered after the light is on, and if does not, touch
[Number Pad] and re-enter.
●
To cancel, press [ ] button and re-enter.
●
If the password is wrong 5 times, “peep” warning alarm will sound 20 times
and the system will shut-down for about 3 minutes. When malfunction
happens, “beep” will sound every 10 seconds, and stop mode will be
turned off automatically after 3 minutes with multiple ‘beeps’.
BIOMETRICS
CARD
Opening the Door from Outside with a Card or Key Tag
The door can be opened from outside using a card or key tag.
Place the registered card or key tag on the card reader.
Placing the Card or Key Tag on the Card Reader
Success:
DING DONG DENG DONG
Fail:
DING DONG DING DONG
Place the card or key tag on
the card reader.
The door will be opened after
1 second.
Opening the Door from the Inside
Available in both a push-pull or pull-push
Warning
●
Please be careful
not to trap your
hand during use.
Automatic
Locking Setting
Manual
Locking Setting
The door is automatically locked 1 seconds after
the door is closed.
The door is locked when the [Close]
button is pressed.
~
When the number pad is lighted, enter
‘4560852580’ and then press the [
] button.
Press and hold the [Register] button for
5 seconds.
DING DONG
DING DING
DING DING
DING DING
Closing the Door from the Inside
Note
●
To check if the door is locked from the inside, press the security button briefly;
the red LED will flash if the door is locked and the blue LED will blink if the door
is unlocked.
●
For 5 seconds after the door is closed, the Bluetooth authentication mode is
not turned on even though you approach the door lock.
(Note that the Bluetooth mode is turned on when you touch the number pad.)
Initialization (Password, Fingerprint, Bluetooth,
Card, Key Tag)
All registered data (password, Fingerprint, Bluetooth, card, key tag) are deleted.
After initialization, the password is set to ‘1234’, and the registered card, key tag
data are erased. Please register a new password after initialization.
1. Pressing the [Register] Button
(from the inside)
2. Entering the Numbers for
Initialization (from the outside)
[Card and Key Tag Registration]
3. Placing the Card or Key Tag on the
Card Reader (from the outside)
4. Confirming Card or Key Tag
Registration (from the outside)
DING DONG DENG
Place the card or key tag to be registered on
the card reader of the outer body. You will
know the card or key tag has been registered
when “DING DONG DENG” sounds.
Place the registered card or key tag
to the card reader on the outer body.
Warning
●
To register multiple cards or key tags, lightly place another card or
key tag to the card reader within 20 seconds after registering the
previous card or key tag.
3. Reading the Fingerprint to Be
Registered
When LED light on the Fingerprint Reading
Panel is on, touch the panel with the finger-
print to be registered. When a “ding” sound
is heard and LED light goes off, then remove
the finger. (Must do it 3 times)
4. Exiting Fingerprint Registration
Mode
To end the registration, please
press the [Registration] button on
the inner body.
DING DONG DENG
[Fingerprint Registration]
Success:
DING DONG DENG
Fail:
DING DONG DING
DONG
DING
Fingerprint, Card and Key Tag Registration
You can register and use up to 100 fingerprints.
Up to 20 cards, including the key tag, can be registered.
(Only ISO14443 A Type is available.)
1. Pressing the [Register] Button
(from the inside)
DING DONG
Open the battery cover of the inner body
and briefly press the [Register] button.
2. Entering the Password
(from the outside)
DING DONG DENG,
DING DING
Enter the password (‘1234’ after initial-
ization) when the number pad is lighted,
and press the [
] button.
- If the security mode is changed as ‘common mode’, second step will be skipped.
Open the door from the outside using the fingerprint authentication system.
Touch the sensor properly with the fingerprint part of your finger which has been
registered.
1. Pressing [Open Fingerprint Cover]
Button
Press the [Open Fingerprint Cover]
button and the lid of the Fingerprint
Reading Panel opens.
2. Reading Fingerprint
Touch the Fingerprint Reading Panel with
the registered fingerprint after LED light
turns on, the lid of the panel closes in ap-
proximately a second later. Then push the
door handle to open the door.
BIOMETRICS
Success:
DING DONG DENG DONG
Fail:
DING DONG DING DONG
Opening the Door from the Outside with a Fingerprint
Activation/Deactivation of the Bluetooth Mode
DING DONG
DING DONG DENG
After the Bluetooth mode is activated, accessing the door lock from the outside
or touching its number pad can authenticate the registered Bluetooth smart-
phone to open the door.
The Bluetooth mode is activated by default.
[11] button: Activate the Bluetooth
mode.
[00] button: Deactivate the Blue-
tooth mode.
Press the [11] or [00] button and the [
] button
to activate or deactivate the Bluetooth mode.
Open the battery cover, and press the
[Register] button shortly.
Note
●
For the information on the pair/unfair of a Bluetooth smart phone,
see the description of application use.
●
Only smart phones with iOS 7.1 or higher and Android 4.3 or
higher support this function. Whether to support Bluetooth, see
the App description.
Pairing of a smart phone
Download “sHome
Doorlock” from
App Store.
Up to eight compatible smart phones can be paired. To pair multiple smart phones,
turn off the Bluetooth of a paired smart phone, and pair another smart phone. If a
Bluetooth smart phone registered is lost, replaced, or repaired and its information
cannot be deleted from the door lock, the door lock should be initialized.
Turn on the Blue-
tooth smart phone.
Open the battery
cover and press the
[REG] button shortly.
DING
DONG
If the number pad
lights, enter ‘88’ and
press the [
] button.
DING
DONG
Enter the password and
press the [
] button.
Enter the 6-digit paring code
displayed in the App of the
phone, and press the [
] button.
The smart
phone is
paired.
Success: DING DONG DENG
DING DONG
Fail: DING DONG DING DONG
Success: DING DONG DENG
Fail: DING DONG DING DONG
Success: DING DONG DENG
Fail: DING DONG DING
DONG
Depending on the direction of the door installed in the residence, customer can
choose from either push-pull type or pull-push type on purchase.
Push
Pull
Pull
Push
Or
GC68-02162A ED01
BIOMETRICS
BIOMETRICS
