background image

Inner Body Parts

BIOMETRICS

OPEN

BIOMETRICS

OPEN

This section contains important information to ensure the user’s 
safety and prevent potential damage to property. Please, read 
this section carefully and use the product accordingly.

Warning

The product components used may vary depending on the installation 
environment.

Outer Body

SHS-H705

www.samsungsds-nss.com/en

GC68-02067B ED:01

USER MANUAL

Convenient Opening

- User friendly access with 

   fingerprints and password

Graphic Interface

- Shows the operation status 

   of the doorlock

Double Authorization

- Requires fingerprint & password 

   combination to open

Double Locking

- Prevents opening from outside

  (Do not disturb)

Built-in Fire Detection

- Generates alarm in case of a fire

Security Function

- Prevents intrusion from the outside

2

Safety Cautions

Product Components

•  The user shall not install or repair the 

product without authorization.

•  Do not install the product in the place 

where the gap between the door and the 

frame is 5mm or more.

•  Make sure that no unauthorized person 

has the access to the password.

•  Do not operate the product with wet 

hands, and keep liquids such as water 

or drinks away from the product, or 

the product may malfunction or be 

damaged.

•  Do not use the excessive force or sharp 

objects to push the lockbuttons, as this 

can damage the product.

•  Make sure that the door is completely 

closed when going outside. The 

manufacturer does not assume the 

responsibility for any harm caused 

by engagement of the lock on an 

improperly closed door.

•  Please do not hang on the product or 

pull it.

•  Be sure to correctly match the poles 

(+/-) when installing the batteries. Install 

the batteries with the correct poles (+/-).

•  Long-term exposure to direct sunlight  

may cause a crack on its touch pad.  

Avoid exposure to direct sunlight during  

installation.

•  During battery replacement, use a new 

one instead of the existing battery.

•  Do not use water, benzene or alcohol 

when cleaning the product, as these 

fluids can cause product malfunction.

•  Replace the batteries within 1 week 

after the battery replacement alarm 

sounds.

Inner Body

User Manual
‘AA’ Batteries (LR6)
Emergency Key (5EA)

Handle Shaft
Handle Shaft Spring
•  Support Panel and Inner 

Body Fastening Bolts

•  Support Panel and Outer 

Body Fastening Bolts

•  Inner Fastening Bolts
•  Strike Fastening Bolts

Number Pad Unlighted

Number Pad Lighted

Number Pad

Open Fingerprint 

Cover Button

Fingerprint 

Reading Panel

Outer Body Handle

Battery Cover

Auto/Manual

Locking Switch
CLOSE Button

Manual Open-

and close

Lever

Sound Control

Switch

Inner body

Handle

Registration

Button

Outer Body Parts

Mortise

Reset Button

Emergency 

Keyhole

External Power 

Port Cover

To setup door lock function, go to main menu.

Main Menu

While the door is open, open 
up the battery cover from the 
inside and press [Register] 
button briefly.

When the light comes on, 
on the number pad, enter 
the master password 
and press [

] button.

The pad is in the
main menu.

How to Change Master Password

Master password must be 4~12 digits long, and only one can be designated as 
the master password.

   

Registered master password cannot be deleted, and can only be changed 
with new password or Initialization of everything (master password, password, 
fingerprints) and reregistration.

Note

1. Entering the main menu (refer to page 4)

2.  Selecting change master 

password menu

3. Entering new master password

When the light comes on, on the 
number pad, press [1] and [

] button.

Enter the new master password  
(4~12 digits) and press [

] button.

DING DONG

Success:  

DING DONG DENG

Fail:  DING-DONG x 2

1. Enter the main menu.
2. Press menu code, then press [

] button.

3. Select the function you want and press [

] button.

Summary of How to Select Modes

3

4

5

6

BIOMETRICS

OPEN

External Power Port

DING 

DONG

DING 

DONG

DENG

Strike 

box

Mortise

(SHS-AML220)

Strike

Mortise

(SHS-AML320)

Strike

Or

Deadbolt

Latch bolt

Open-door sensor

SHS-AML320

SHS-AML220

When purchased, the product is set to Multi-leveled Security Code Entry Mode 
initially. Please refer to “How to Set Up Multi-leveled Security Code Entry Mode” 
for Common Mode setting.

Opening the Door from Outside with a Password

1. Multi-leveled Security Code Entry Mode

Touching [Number 
Pad] will light up the 
number pad.

When two arbitrary 
buttons are lighted,  
press the buttons in 
order.

When the numbers on the 
number pad are lighted, 
enter the password and 
press the [

] button.

Success:  DING DONG 

DENG DONG

Fail:  DING-DONG x 2

   

Password must be entered after the light is on, and if does not, touch 
[Number Pad] and re-enter.

   

To cancel, press [   ]  button and re-enter.

   

If the password is wrong 5 times, “peep” warning alarm will sound 20 times 
and the system will shut-down for about 3 minutes. When malfunction 
happens, “beep” will sound every 10 seconds, and stop mode will be turned 
off automatically after 3 minutes with multiple ‘beeps’.

Note

2. Common Mode

If the security mode is changed as ‘common mode’, second step will be skipped.

Use fingerprint to open the door from the outside. While the LED light is on, 
place the finger with the registered fingerprint in the correct way.

Opening the Door from the Outside with a 

Fingerprint

1.  Pressing [Open Fingerprint  

Cover] button

2.  Reading Fingerprint

The cover for the 
fingerprint reading panel 
will open when [Open 
Fingerprint Cover] 
button is pressed.

When the LED light comes on, on [Fingerprint 
Reading Panel], place fingerprint and wait for 
about 1 second. When the door is unlocked, 
fingerprint reading panel cover will close, and door 
can be opened by pressing the handle downward.

Success:  

DING DONG 

DENG DONG

Fail:  

DING-DONG x 2

BIOMETRICS

OPEN

OPEN

Pulling down the Door Lock Handle

Rotate the manual Open/Close lever 
to the right or left to lock the door or 
release the locking.

Rotating the Manual Open/Close 
Lever to the Right or Left

Rotate the door lock handle of the inner 
body downward.

Opening the Door from the Inside

Closing the Door from the Outside

Touch [Number Pad]

If you go outside while in manual locking mode, 

touch [Number Pad] on the outer body.

Press [Open Fingerprint  

Cover] button

If you go outside while in manual locking mode, 

touch [Open Fingerprint Cover] on the outer body.

Press and hold the [Register] 
button for 3 seconds.

When the number pad is lighted, enter 
‘4560852580’ and then press the [

button.
- Success : DING DONG DENG
- Fail : DING-DONG x 2

Delete all data. When data is being Initialization, new master password will be 
‘1234’ and previously registered fingerprints and password will be deleted.

Initialization (master password, password, 

fingerprint)

DING DONG 

DING DONG

1.  Pressing the [Register] Button 

(from the inside)

2.  Entering the Numbers for 

Initialization (from the outside)

Closing the Door from the Inside

Automatic 
Locking Setting

The door is automatically locked  

2 seconds after the door is closed.

Manual
Locking Setting

The door is locked when the [Close] 

button is pressed.

Change master password

New master

password

Code

number (0~9)

Code

number (0~9)

New password

Read fingerprint

1

st

confirmation

2

nd

confirmation

Register password

Delete password individually

Delete all passwords

Register fingerprint

Delete fingerprint individually

Delete all fingerprints

Set Up double 

authorization Mode

Turn off double

authorization Mode

Set Up Multi-leveled Security 

Code Entry Mode

Turn off doubleSecurity mode

Read fingerprint

1

4

5

6

7

8

9

0

0

0

0

4

6

7

9

Main
menu

3

2

1

Reviews: