✎
By connecting the TV to a receiver or home theater with
Dolby Digital
and 5.1ch speakers and selecting
Dolby
Digital
, you can maximize your interactive 3D sound
experience.
■
Audio Delay
: Lets you correct timing mismatches between the
audio track and the video when you are watching the TV and
listening to digital audio output from the TV through an external
device such as an AV receiver. When you select
Audio Delay
, a
slider appears. Use the left and right arrow buttons to adjust the
slider. Press
ENTER
E
when done (0ms ~ 250ms).
Speaker Settings
■
Speaker Select (External Speaker / TV Speaker)
If you are listening to the sound track of a broadcast or movie
through an external receiver, you may hear a sound echo caused
by the difference in decoding speed between the TV’s speakers
and the speakers attached to your audio receiver. If this occurs, set
the TV to
External Speaker
.
✎
When you set
Speaker Select
to
External Speaker
, the
TV’s speakers are turned off. You will hear sound through the
external speakers only. When you set
Speaker Select
to
TV
Speaker
both the TV’s speakers and the external speakers
are on. You will hear sound through both.
✎
When
Speaker Select
is set to
External Speaker
, the
VOLUME
and
MUTE
buttons will not operate and the sound
settings will be limited.
✎
If there is no video signal, both the TV’s speakers and the
external speakers will be mute.
Sound Reset
■
Reset All
: Resets all sound settings to the factory defaults.
Channel Menu
❑
Memorizing Channels
When you first set up your TV using
Plug & Play
, the TV memorized
the channels that were available over the air or through your cable
system and added them to the
Channel List
. The
Antenna
and
Auto program
functions described below let you re-run the channel
memorization function without having to re-run the
Plug & Play
procedure.
Antenna (Air / Cable)
t
Before your television can memorize the available channels, you
must select your TV's signal source,
Air
(using an antenna) or
Cable
.
Select Menu >
Channel
>
Antenna
>
Air
or
Cable
. After you have
selected the signal source, go on to the Auto Program function.
✎
Selecting the signal source using the
Antenna
function also
determines the signal source the TV is tuned to. For example,
if you receive your TV signal over the air, and you select
Cable
,
you will see only snow. You must select Air to see a picture.
Auto Program
The
Auto Program
function memorizes all channels that are
available over the air or through your cable system and adds them to
the
Channel List
.
To start
Auto Program
, follow these steps:
1. Push
MENU
m
→
Channel
→
ENTER
E
on your remote. The
Antenna Source screen appears.
2. On the Antenna Source screen, select the source of your TV
signal.
Air
If your TV is connected to an antenna choose
Air
, and then press
ENTER
E
. The TV will automatically start memorizing channels.
Cable
If your TV is connected to a cable outlet, choose
Cable
, and then
press
ENTER
E
.
Go to Step 3.
Auto
If you choose Auto, and then press
ENTER
E
, the TV will
automatically select the correct Antenna source. Go to Step 3.
3. On the Cable Type screen, use the
◄/►/▲/▼
buttons to select
the type of digital and analog cable systems you have:
STD
,
HRC
,
or
IRC.
Most systems are
STD
(Standard). When done, select
Start
, and then press
ENTER
E
. The TV will start memorizing
channels.
✎
Channel memorization can take up to 45 minutes, depending
on your cable system.
✎
Memorized channels are added to the
Added Channel
list. These are the channels you will see when you use the
Channel buttons on your remote.
Clear Scrambled Channel
This function filters out scrambled channels after
Auto Program
is
completed. This process may take up to 20~30 minutes.
✎
Press the
ENTER
E
button to stop the
Clear Scrambled
Channel
.
✎
This function is only available in
Cable
mode.
❑
Managing Channels
Channel List
See your list of Added channels, Favorite channels, or channels
you've scheduled for viewing. Add or delete Favorite channels, add
or delete channels from the Added Channels list, schedule channels
or programs for viewing. Watch a channel by selecting the channel
in the
All Channels, Added Channels
, or
Favorite
screen, pressing
the
▲
/
▼
buttons, and then pressing the
ENTER
E
button.
Added Channels
6
Air
6-1
♥ TV #6
7-1
♥ TV #7
8
Air
9
Air
9-1
♥ TV #9
10
Air
10-1
♥ TV #10
11-1
♥ TV #11
Air
'
Zoom
'
Select
T
Tools ► Next Program
Channel List Screens icons are listed on the left side. Select an
icon using the
▲/▼
buttons to view each list.
■
All Channels
: Shows all currently available channels including
those you deleted from the
Added channels
list.
■
Added Channels
: Shows all
Added channels
. These are the
channels that appear when you press the CH button.
■
*
Favorite
: Shows all favorite channels.
■
Programmed
: Shows all channels and programs currently
scheduled using
Timer Viewing
.
✎
Remote control buttons active on the
Channel List
screen.
x
Green (
Zoom
): Enlarges or shrinks a channel number.
x
Yellow (
Select
): Move the cursor to a channel. Press the Yellow
button to select the channel. A
c
mark appears. Repeat to select
additional channels. Then, open the Tools menu and apply a
function to the channels you selected.
x
T
(
Tools
): Displays the
Channel List
Tools
menu. (The
Tools
menus may differ depending on the situation.)
Input Source
Picture Size
ATV, AV, Component (480i, 480p)
16:9
,
Zoom1
,
Zoom2
,
4:3
DTV (1080i, 1080p), Component (1080i,
1080p), HDMI (720p, 1080i, 1080p)
16:9
,
Wide Fit
,
4:3
,
Screen Fit
■
Digital Noise Filter (Off / Low / Medium / High / Auto)
: If the
broadcast signal received by your TV is weak, you can activate
the
Digital Noise Filter
feature to reduce any static and ghosting
that may appear on the screen.
✎
When the signal is weak, try all the Digital Noise Filter
options until the TV displays the best picture.
■
HDMI Black Level (Normal / Low)
: For HDMI signals, select
the black level to adjust the screen depth. Low make blacks look
darker.
✎
Available only in
HDMI
mode (RGB signals).
■
Film Mode (Off / Auto)
: Sets the TV to automatically sense and
process film signals from all sources and adjusts the picture for
optimum quality.
✎
Available in ATV, DTV (interlace), AV, COMPONENT (480i /
1080i) and HDMI (480i / 1080i).
■
Screen Burn Protection
: To reduce the possibility of screen
burn, this unit is equipped with Pixel Shift screen burn prevention
technology. Pixel Shift moves the picture slightly on the screen.
The Time function setting allows you to program the time
between movement of the picture in minutes.
x
Pixel Shift (Off / On) : Using this function, you can set the TV
to move pixels minutely on the PDP screen in a horizontal or
vertical direction to minimize after images on the screen.
Available Pixel Shift Settings and Optimum Settings
Available Settings
Optimum Settings
Horizontal
0~4 (pixels)
4
Vertical
0~4 (pixels)
4
Time
(minute)
1~4 min
4 min
✎
The
Pixel Shift
value may differ depending on the
monitor size (inches) and mode.
✎
This function is not available in the
Screen Fit
mode.
Your TV also has the following additional screen burn
protection functions:
x
Scrolling
: This function removes after-images on the screen
by illuminating all the pixels on the PDP according to a pattern.
Use this function when there are after images or symbols on
the screen, especially when you displayed a still image on the
screen for a long time.
✎
The after-image removal function has
to run a long time
(approximately 1 hour) to remove after-images on the
screen effectively. If the after-image is not removed after
you run the function, run the function again.
✎
Press any key on the remote control to cancel this
feature.
x
Side Grey
(Dark/Light)
: Lets you select the color of the
sidebars your TV displays when you set the screen size to 4:3.
■
Picture Reset (Reset Picture Mode/Cancel)
: Resets the
picture settings to their factory defaults.
Sound Menu
Mode
t
■
Standard
: Selects the normal sound mode.
■
Music
: Emphasizes music over voices.
■
Movie
: Provides the best sound for movies.
■
Clear Voice
: Emphasizes voices over other sounds.
■
Amplify
: Increase the intensity of high-frequency sounds to allow
a better listening experience for the hearing impaired.
Equalizer
Available in Standard sound mode only.
■
Balance L/R
: Adjusts the balance between the right and left
speaker.
■
100Hz / 300Hz / 1KHz / 3KHz / 10KHz
(Bandwidth
Adjustment): Adjusts the loudness of specific bandwidth
frequencies.
■
Reset
: Resets the equalizer to its default settings.
SRS TruSurround HD (On/Off)
Available in Standard sound mode only.
SRS TruSurround HD is a patented SRS technology that solves
the problem of playing 5.1 multichannel content through two
speakers. TruSurround delivers a compelling, virtual surround
sound experience through any two-speaker playback system,
including internal television speakers. It is fully compatible with all
multichannel formats.
Preferred Language
Digital channels only.
Digital-TV broadcasts can transmit many audio tracks
simultaneously (for example, simultaneous translations of a program
into foreign languages).
✎
You can only select a language from among the ones being
broadcast.
Multi-Track Sound (MTS)
Analog channels only.
■
Mono
: Select for channels that are broadcasting in mono or if
you are having difficulty receiving a stereo signal.
■
Stereo
: Select for channels that are broadcasting in stereo.
■
SAP
: Select to listen to the Separate Audio Program, which is
usually a foreign-language translation.
✎
Depending on the program being broadcast, you can listen to
Mono, Stereo
or
SAP
.
Auto Volume
Because each station has its own broadcasting conditions, the
volume may fluctuate each time you change the channel. This
feature automatically adjusts the volume of a channel by lowering
the sound output when the modulation signal is high or by raising
the sound output when the modulation signal is low.
SPDIF Output
The SPDIF (Sony Philips Digital InterFace) outputs an
uncompressed digital audio signal when you connect the digital
audio jack on the back of the TV to a digital audio in jack on a
receiver or home theater.
■
Audio Format (PCM/Dolby Digital)
: You can select the Digital
Audio output (SPDIF) format. The available Digital Audio output
format may differ depending on the input source.
Display Icons Used in the Channel List Screens
Icons
Meaning
c
A selected channel.
*
A Favorite channel.
)
A reserved program.
(
A program currently being broadcast.
❑
The Channel List Tools Menu
t
The Channel List Tools menu contains most of the functions you
can use on the
All Channel
,
Added Channels
, and
Favorite
List
screens. To view, select a list screen, select a channel, and then
press the
TOOLS
button.
■
Add / Delete
: Delete a channel from or add a channel to the
Added Channels
list.
To delete channels from the
Added Channels
list, follow these
steps:
1. Select one or more channels in the
Added Channels
list
using the
▲/▼
buttons and the Yellow Select button on your
remote.
2. Press the
TOOLS
button on your remote. The Tools menu
appears
.
3. Select
Delete
in the Tools menu, and then press the
ENTER
E
button.
To add channels to the
Added Channels
list, follow these steps:
1. Select one or more channels in the
All Channels
list using the
▲/▼
buttons and the Yellow Select button on your remote.
2. Press the
TOOLS
button on your remote. The Tools menu
appears
.
3. Select
Add
in the Tools menu, and then press the
ENTER
E
button.
✎
All deleted channels will be shown on the
All Channels
list.
You add channels back to the
Added Channels
list on the
All Channels
list.
✎
A gray-colored channel indicates the channel has been
deleted from the
Added Channels
list.
✎
The
Add
menu option only appears for deleted channels.
■
Add to Favorite/Delete from Favorite
t
: Lets you add
channels to and delete channels from your
Favorites
list.
To add channels to the Favorites list, follow these steps:
1. Select one or more channels in the
All Channels
list using the
▲/▼
buttons and the Yellow Select button on your remote.
2. Press the
TOOLS
button on your remote. The Tools menu
appears
.
3. Select
Add to Favorite
in the Tools menu, and then press the
ENTER
E
button.
To delete channels from the
Favorites
list, follow these steps:
1. Select one or more channels in the
Favorite
Channels list
using the
▲/▼
buttons and the Yellow Select button on your
remote.
2. Press the
TOOLS
button on your remote. The Tools menu
appears.
3. Select
Delete from Favorite
in the Tools menu, and then
press the
ENTER
E
button.
■
Timer Viewing
: You can schedule a channel to be displayed
automatically at a set time, even when you are watching another
channel. You must set the current time first in the
Time
>
Clock
function to use
Time Viewing
.
To schedule a channel, follow these steps:
1. Select a channel in the
Added Channels
list using the
▲/▼
buttons and the Yellow Select button on your remote.
2. Press the
TOOLS
button on your remote. The Tools menu
appears
.
3. Select
Time Viewing
in the Tools menu, and then press the
ENTER
E
button. The Time Viewing screen appears.
Antenna
Channel
Repeat
▲
DTV Air
6-1
Once
▼
L
Move
U
Adjust
E
Enter
R
Return
Timer Viewing
Date
Start Time
01-01-2012
12 : 01 am
4. Use the
◄/►
buttons to move from entry field to entry field
and the
▲/▼
buttons to change the entries. Where numbers
are displayed, you can also enter numbers directly using the
number keypad on your remote.
✎
If you select
Everyday
or
Every Week
, the date you
select in the Date field becomes the start date for your
scheduled viewing. For
Everyday
, the TV will turn on
every day, at the time you selected, starting from that
date. For
Everyweek
, the TV will turn on every week,
on the same day of the week as the start date you
selected, at the time you selected, from that day on. If
you select
Once
, the TV will turn on once, on the date
and time you selected.
5. Press the
ENTER
E
button on your remote when done.
✎
Only
Added channels
can be scheduled.
✎
Scheduled programs and channels are displayed in the
Programmed
List.
✎
When you select a digital channel, press the
►
button to
view the digital program list. If you highlight a program in
the list, and then press the
ENTER
E
(
Schedule
) button,
you set
Timer Viewing
for that program directly.
■
Select All
: Select all the channels in the displayed channel list.
■
Deselect All
: Deselect all the selected displayed channels.
✎
You can only select
Deselect All
when one or more
channels are selected.
■
Channel Name Edit
: Analog channels only. Lets you assign a
name of up to five characters to an analog channel. For example,
Hist, Food, Golf, etc. This makes it easier to find and select a
channel .
■
Auto Program
: See
Auto Program
under Memorizing Channels.
Programmed List (on the Channel List Screen)
The
Programmed
list displays the channels and programs you
have scheduled for viewing using the
Time Viewing
function. You
can view, modify, or delete a show you have scheduled using the
functions on the
Programmed
List screen Tools menu.
Programmed List Screen Tools Menu
t
■
Change Info
: Change the scheduling information for a show or
channel you have scheduled.
To change the information, follow these steps:
1. Select the
Programmed
List icon on the left side of the
Channel List
screen, and then press the
ENTER
E
button.
2. On the
Programmed
List screen, select the show or channel
entry you want to change, and then press the
TOOLS
button.
The Tools Menu appears.
3. Select
Change Info
, and then press the
ENTER
E
button.
The
Time Viewing
screen appears.
4. Use the
◄/►
buttons to move from entry field to entry field
and the
▲/▼
buttons to change the entries. Where numbers
are displayed, you can also enter numbers directly using the
number keypad on your remote.
5. Press the
ENTER
E
button when done.
■
Cancel Schedules
: Cancel a show or channel you have
scheduled.
To cancel a scheduled show or channel, follow these steps:
1. Select the
Programmed
List icon on the left side of the
Channel List
screen, and then press the
ENTER
E
button.
2. On the
Programmed
List screen, select the show or channel
entry you want to cancel, and then press the
TOOLS
button.
The Tools Menu appears.
3. Select
Cancel Schedules
, and then press the
ENTER
E
button. The
Cancel Schedule
screen appears.
4. Select
OK
, and then press the
ENTER
E
button.
■
Information
: Display the information for a show or channel you
have scheduled. You can also change the schedule Information.
1. Select the
Programmed
List icon on the left side of the
Channel List
screen, and then press the
ENTER
E
button.
2. On the
Programmed
List screen, select the show or channel
entry you want information for, and then press the
TOOLS
button. The Tools Menu appears.
3. Select
Information
, and then press the
ENTER
E
button.
The
Time Viewing
Information screen appears.
4. Select
Change Info
and press the
ENTER
E
button
to change information, or select
Close
and press the
ENTER
E
button to close the Information screen.
■
Select All / Deselect All
: You can select or deselect all
channels in the channel list.
❑
Other Channel Menu Functions
Channel Mode (Added Channels/Favorite
Channels)
Lets you select the channel list displayed when you press the
<
CH
>
(Channel) button on your remote. For example, if you
select Favorite Channels, you will only see Favorite channels when
you press the
<
CH
>
button.
Fine Tune
Analog channels only.
If the reception is clear, you do not have to fine tune the channel,
as this is done automatically during the search and store
operation. If the signal is weak or distorted, fine tune the channel
manually.
✎
Select the channel, and then select
Fine Tune
.
✎
Fine tuned channels that have been saved are marked with
an asterisk “*” on the right-hand side of the channel number
in the channel banner.
✎
To reset fine-tuning, select the channel, select
Fine Tune
, and
then select
Reset
on the
Fine Tune
screen.
Setup Menu
Plug & Play
Lets you re-run the
Plug & Play
initial setup procedure. For
instructions, see your Quick Start Guide.
Language
Set the menu language.
✎
Choose between
English
,
Español,
and
Français
.
❑
Setting the Time
Time
✎
The time you set will appear when you press the
INFO
button.
■
Clock
: Set the clock so you can use the various timer features
of the TV.
✎
If you disconnect the power cord, you have to set the
clock again.
To set the clock, follow these steps
:
1. Select
Setup
>
Time
>
Clock
.
2. Press
ENTER
E
and select
Auto
or
Manual
, and then press
ENTER
E
again.
If you selected Auto:
The TV will automatically download the correct time from a
digital channel.
•
Select
Time Zone
, and then press the
ENTER
E
button.
Use the
▲/▼
buttons to select your
Time Zone
, and then
press
ENTER
E
.
•
Select DST (Daylight Savings Time), and then press
ENTER
E
. Select
On
if you want to turn the DST
adjustment on and off manually. Select
Off
to turn off the
DST adjustment. Select
Auto
if you want the TV to adjust
to DST automatically. Press
ENTER
E
when done.
✎
DST
and
Time Zone
function are only available when
the
Clock Mode
is set to
Auto
.
If you selected Manual:
The
Clock Set
screen appears. Use the
▲/▼
buttons to
change the values in each field or use the number buttons to
enter the values directly. Use the
◄/►
buttons to move from
field to field. When done with all the fields, press
ENTER
E
.
✎
Available only when
Clock Mode
is set to
Manual
.
■
Sleep Timer
t
Automatically shuts off the TV after a preset period of time. (30,
60, 90, 120, 150 and 180 minutes).
✎
To cancel the
Sleep Timer
, select
Off
.
Timer 1 / Timer 2 / Timer 3
Turns the TV on and off automatically at times and days you
select. You can set three different on/off timer settings.
✎
You must set the clock first.
■
On Time / Off Time
: Set the hour, minute, am/pm, and
Activate/Inactivate fields for the
On Time
and
Off Time
. Use the
◄/►
buttons to move from field to field. Use the
▲/▼
buttons
to change the values in each field. To activate the timer with
the setting you have chosen, set the Activate/Inactivate field to
Activate
.
■
Volume
: Set the desired loudness.
Figures and illustrations in this User Manual are provided for reference
only and may differ from actual product appearance. Product design and
specifications may be changed without notice.
Important Warranty Information Regarding
Television Format Viewing
✎
See the warranty card for more information on warranty terms.
Wide screen format PDP Displays (with 16:9 aspect ratios, the ratio of the
screen width to height) are primarily designed to view wide screen format
full-motion video. The images displayed on them should primarily be in the wide
screen 16:9 ratio format, or expanded to fill the screen if your model offers this
feature, with the images constantly in motion. Displaying stationary graphics
and images on the screen, such as the dark sidebars on non-expanded
standard format television video and programming, should be limited to no
more than 5% of the total television viewing per week.
Additionally, viewing other stationary images and text such as stock market
crawls, video game displays, station logos, web sites or computer graphics and
patterns, should be limited as described above for all televisions. Displaying
stationary images for more than 5% of total viewing time can cause uneven
aging of your PDP display and leave subtle, but permanent burned-in ghost
images in the PDP picture. To avoid this, vary the programming and images,
and primarily display full screen moving images, not stationary patterns or dark
bars. On PDP models that offer picture sizing features, use these controls to
view different formats as a full screen picture.
Be careful in the selection of television formats you use for viewing and the
amount of time you view them. Uneven PDP aging as a result of format
selection and use, as well as burned in images, are not covered by your
Samsung limited warranty.
• SAMSUNG ELECTRONICS NORTH AMERICAN LIMITED WARRANTY
STATEMENT
Subject to the requirements, conditions, exclusions and limitations of the original
Limited Warranty supplied with Samsung Electronics (SAMSUNG) products,
and the requirements, conditions, exclusions and limitations contained herein,
SAMSUNG will additionally provide Warranty Repair Service in the United States
on SAMSUNG products purchased in Canada, and in Canada on SAMSUNG
products purchased in the United States, for the warranty period originally
specified, and to the Original Purchaser only.
The above described warranty repairs must be performed by a SAMSUNG
Authorized Service Center. Along with this Statement, the Original Limited
Warranty Statement and a dated Bill of Sale as Proof of Purchase must be
presented to the Service Center. Transportation to and from the Service Center
is the responsibility of the purchaser. Conditions covered are limited only to
manufacturing defects in material or workmanship, and only those encountered
in normal use of the product.
Excluded, but not limited to, are any originally specified provisions for, in-
home or on-site services, minimum or maximum repair times, exchanges or
replacements, accessories, options, upgrades, or consumables.
For the location of a SAMSUNG Authorized Service Center, please call toll-free:
– In the United States : 1-800-SAMSUNG (1-800-726-7864)
– In Canada : 1-800-SAMSUNG
Important User Information
•
Screen Image retention
Do not display a still image (such as that from a video game) on the plasma
display panel for more than a few minutes. Still images can cause screen
image retention (burn in). To avoid such image retention, reduce the degree
of brightness and contrast of the screen when displaying a still image.
•
Heat on the top of the Plasma TV
The top side of the TV may become hot after long periods of use as heat
dissipates from the panel through the vent hole in the upper part of the TV.
This is normal and does not indicate any defect or operational failure of unit.
However, children should be prevented from touching the upper part of
the TV.
•
The TV is making a ‘cracking’ noise.
A ‘cracking’ noise may occur when the TV contracts or expands due
changes in the surrounding environment such as temperature or humidity.
This is normal and not a def
ect.
•
Cell Defects
Your plasma TV has a panel containing 2,360,000 (HD-level) to 6,221,000
(FHD-level) pixels which require sophisticated technology to produce.
However, there may be a few bright or dark pixels on the screen. These
pixels will have no impact on the performance of the product.
•
Avoid operating the TV at temperatures below 41°F (5°C)
•
A still image displayed too long may cause permanent damage to the
PDP Panel.
Watching the Plasma TV in 4:3 format for a long period of
time may leave traces of the borders on the left, right, top, or
bottom of the screen. Playing a DVD or a game console may
have a similar effect. Damage caused by the above effect is
not covered by the warranty.
•
After-images on the Screen.
Displaying still images from Video games or a PC for longer than a certain
period of time may produce partial after-images. To prevent this effect,
reduce the ‘brightness’ and ‘contrast’ when displaying still images for a
long time.
•
Warranty
Warranty does not cover any damage caused by image retention.
Burn-in is not covered by the warranty.
•
Caution
The glass screen of your PDP TV can break if you accidently drop the TV. Handle
the TV with care. When moving the TV, always have two or more people pick it
up and carry it as a safety precaution. Do not lay the TV flat on its face or back.
Your Samsung Plasma TV is a high quality television that has been carefully packaged to protect
the integrity of its glass panel and component parts during shipment. It is, nonetheless, a fragile
piece of electronics that requires careful handling. Refrain from putting undue stress on any part
of the packaging when shipping or unpacking the TV. Use care when installing the TV. Avoid
placing the TV in a location where it may be struck, exposed to sharp impacts, or fall. Panel
breakage caused by a fall or impact strike is not covered under the manufacturer’s warranty.
BN68-04647A
BN68-04647A-00
Plasma TV
user manual
The On Screen Menus
Your TV has two kinds of menus, the Main menu and the various
Tools menus. The Main menu gives you access to most or all of
the menu options available on your TV. The Tools menus display
a selected number of frequently used menu options that change
depending on the screen you are viewing. A Tools menu symbol
(
T
) in the lower right side of the screen indicates that a Tools menu
is available.
The Main menu has seven primary categories:
y
Picture
y
Input
y
Sound
y
Application
y
Channel
y
Support
y
Setup
To view the Main menu, press the
MENU
button on your remote. To
view a Tools menu, press the
TOOLS
button on your remote.
✎
The menu options that appear in the Main menu depend
on the Source you have selected. For example, if you have
selected the HDMI source, the Channel category will not
appear. To see the Channel category, you must first select TV
in the Source List.
The Menu options are presented below, arranged by Main menu
categories. A Tools button symbol (
t
)
next to an option
name indicates the option is also available in one of the Tools
menus.
Picture Menu
Mode
t
Select your preferred picture mode.
✎
When your TV is connected to a PC, you can only select
Entertain
and
Standard
.
■
Dynamic
: Brightens the screen. Suitable for a bright room.
■
Standard
: Suitable for a normally lit room.
■
Movie
: Darkens the screen, making it less glary. Suitable for
watching movies in a darkened room.
■
Entertain
: Sharpens the picture. Suitable for games.
✎
Only available when the
TV
is connected to a
PC
.
Cell Light / Contrast / Brightness / Sharpness /
Color / Tint (G/R)
■
Cell Light
: Adjusts the brightness of the screen by adjusting the
brightness of the individual pixels.
■
Contrast
: Increases or decreases the contrast between dark and
light areas of the picture.
■
Brightness
: Adjusts the brightness of the screen. Not as
effective as Cell Light.
■
Sharpness
: Sharpens or dulls the edges of objects.
■
Color
: Adjusts the color saturation. The higher the Color setting,
the more intense the color. Low settings remove color and the
picture becomes black, white, and gray.
■
Tint
: Adjusts the amount of green and red in the picture. As you
increase the amount of green, the amount of red decreases and
vice versa.
✎
When the TV is connected to a PC, you can only make
changes to
Cell Light, Contrast, Brightness,
and
Sharpness.
Advanced Settings
Available in
Standard
and
Movie
mode only.
Compared to previous models, new Samsung TVs offer a more
precise picture with more precise controls.
✎
When your TV is connected to a PC, you can only make
changes to
Gamma
and
White Balance
.
■
Color Space (Auto / Native)
: Auto automatically matches the
range of colors available to create pictures to the color range of
the video source. Native provides a color range wider than the
color range of the video source.
■
White Balance
: Adjusts the color temperature of the picture so
that white objects look white (instead of, for example, slightly
pink or slightly yellow) and the overall color of the picture looks
natural.
R-Offset / G-Offset / B-Offset
: Adjusts each color’s (red,
green, blue) darkness.
R-Gain / G-Gain / B-Gain
: Adjusts each color’s (red, green,
blue) brightness.
Reset
: Resets the
White Balance
to it’s default settings.
■
Gamma
: Adjusts the primary color intensity.
■
Dynamic Contrast (Off / Low / Medium / High)
: Adjusts the
screen contrast.
■
Black Tone (Off / Dark / Darker / Darkest)
: Selects the black
level to adjust the screen depth. Darker settings make blacks
look darker.
■
Flesh Tone
: Adjusts the amount of red in skin tones.
■
Motion Lighting (Off / On)
: When on, the TV automatically
adjusts the brightness of the screen in response to the
brightness of the room. In bright light, the screen brightens. In
dim light, the screen dims.
✎
Available in
Standard
mode only.
Picture Options
✎
When the TV is connected to a PC, you can only make
changes to the
Color Tone
,
Size
and
HDMI Black Level
.
■
Color Tone (Cool / Standard / Warm1 / Warm2)
: Cool makes
the picture bluer (cooler). Warm 1 and Warm 2 make the picture
redder (warmer).
✎
Warm1
and
Warm2
are deactivated when the picture
mode is set to
Dynamic
.
■
Size
: Set the size and aspect ratio of the picture on the screen.
Your cable box or satellite receiver may have its own set of
screen sizes as well. However, we highly recommend you use
the TV's 16:9 mode most of the time.
16:9
: Sets the picture to the 16:9 wide screen format.
Zoom1
: Provides moderate magnification of the picture. Sides,
top, and bottom are cut off.
Zoom2
: Provides larger magnification of the picture. Sides, top,
and bottom are cut off.
Wide Fit
: Enlarges the aspect ratio of the picture so the picture
fits the entire screen.
4:3
: Sets the picture to the old, 4:3 format and puts black or gray
borders on the right and left of the picture.
✎
Do not watch your TV in the 4:3 format for a long time.
Traces of borders displayed on the left, right and center of
the screen may cause image retention (screen burn) which
is not covered by the warranty.
Screen Fit
: Displays the full image without any cut-off when
your TV is inputting HDMI (720p / 1080i / 1080p) or Component
(1080i / 1080p) HD signals.
✎
HD (High Definition) has a 16:9 aspect ratio and 1080i/1080p
(1920x1080) or 720p (1280x720) resolution.
✎
You can adjust and store settings for each external device you
have connected to an input on the TV. Picture Sizes available
by Input Source are listed above and to the right:
© 2012 Samsung Electronics Co., Ltd. All rights reserved.
■
Contents
: To select what will be turned on when the timer
setting is activated. You can set the TV to turn on a specific
channel or play back contents such as photo or audio files.
Use the
◄/►
buttons to move to move to the Contents field,
and then press the
ENTER
E
button. The Contents screen
appears. Use the
◄/►
buttons to move from field to field. Use
the
▲/▼
buttons to change the values in each field.
- TV/USB
: Select
TV
or
USB
. The USB device must be
connected to your TV before you can select USB.
- Antenna
: Displays the current antenna source,
Air
or
Cable
.
- Channel
: If you have selected TV, select the desired channel.
- Music/Photo
: If you have selected USB, follow these steps to
select a folder containing MP3 (Music) or JPEG (Photo) files on
the USB device:
✎
The maximum displayed number of files, including sub
folders, in one folder of USB storage device is 2000.
✎
The media may not be playing smoothly when using the
device lower than USB 2.0.
1. Use the
◄/►
buttons to move to the field under
Music
or the field under
Photo
, and then press the
ENTER
E
button. The TV displays a single folder (the Root folder) and
the type or name of the device.
2. Press the
ENTER
E
button. A list of folders on the device
appears.
✎
If there are no folders on your device, press the
Yellow
select button to select the Root folder, and
then press the
RETURN
button. The Timer screen
re-appears.
3. Use the
▲/▼
buttons to highlight a folder that contains
music or photos, and then press the
Yellow
select button
to select the folder.
4. Press the
RETURN
button. The Timer screen re-appears.
■
Repeat
: Select
Once
,
Everyday
,
Mon~Fri
,
Mon~Sat
,
Sat~Sun
or
Manual
. If you select
Manual
, you can select the days you
want to activate the timer by using the
◄/►
buttons to highlight
the day, and then pressing the
ENTER
E
button. To unselect a
day, highlight it, and then press the
ENTER
E
button.
When you finished making all your selections on the Timer screen,
press either the
ENTER
E
or
RETURN
button.
❑
Other Features
Program Rating Lock
The
Program Rating Lock
feature lets you block programs
you've determined are inappropriate for your children based on
the program's ratings. To access the
Program Rating Lock
feature and make any changes, you must enter a PIN (personal
identification number). To watch a blocked program, you must also
enter the same PIN.
✎
Program Rating Lock
is not available in
HDMI
or
Component
mode.
✎
The default PIN number of a new TV set is “0-0-0-0”. You can
set your own PIN using the
Change PIN
function.
How It Works
When you access the
Program Rating Lock
Menu functions for
the first time, the PIN input screen appears. Enter 0-0-0-0. The PIN
screen closes and the
Program Rating Lock
Menu appears. Every
time you access the
Program Rating Lock
functions, the PIN
screen will appear and you must enter a PIN.
When the Rating Lock screen appears, select
Program Rating
Lock
, and then press
ENTER
E
. Select
ON
, and then press the
ENTER
E
key again. Depending on what type of programs or
movies you want to block, select one of the options on the screen,
and then press the
ENTER
E
button. The options are listed below:
■
TV Parental Guidelines
: You can block TV programs based
on their ratings. This function allows you to control what your
children are watching.
■
MPAA Rating
: You can block movies based on their MPAA
ratings. The Motion Picture Association of America (MPAA) has
implemented a rating system that provides parents or guardians
with advanced information on which films are appropriate for
children.
■
Canadian English
: You can block TV programs based on their
Anglophone Canadian ratings.
■
Canadian French
: You can block TV programs based on their
French Canadian ratings.
■
Downloadable U.S. Rating
: Parental restriction information can
be used while watching DTV channels.
Locking/Blocking Programs or Movies
You lock or block programs and/or movies in essentially the same
way for each option. Each option displays a grid or table. All the
tables have ratings listed on the left. The TV Parental Guidelines
option also has kinds of content listed across the top:
ALL
: Lock all
TV ratings. /
FV
: Fantasy violence /
V
: Violence /
S
: Sexual situation
/
L
: Adult Language /
D
: Sexually Suggestive Dialog.
To lock/block movies or shows with certain ratings and/or kinds of
content, click the square next to the rating and/or under the kind of
content. A lock appears. To unlock/unblock, click the square again.
When you click a low rating, all the ratings above it will also display
locks. You can also Allow All or Lock All. When done, press the
RETURN
button on your remote.
■
Change PIN
: The Change PIN screen will appear. Choose any
4 digits for your PIN and enter them in
Enter New PIN
fields.
Re-enter the same 4 digits in
Confirm New PIN
fields. When the
Change PIN screen disappears, press the
OK
button. The TV
has memorized your new PIN.
✎
If you forget the PIN, press the remote-control buttons in
the following sequence, which resets the pin to “0-0-0-0” :
POWER
(off)
→
MUTE
→
8
→
2
→
4
→
POWER
(on)
Game Mode (On/Off)
When you connect a game console such as a PlayStation™
or Xbox™ to your TV, you can enjoy a more realistic gaming
experience by turning on the
Game Mode
function.
✎
Precautions and limitations for game mode:
x
Before you disconnect the game console and connect another
external device, set
Game Mode
to
Off
in the setup menu.
x
If you display the TV menu in
Game Mode
, the screen shakes
slightly.
✎
Game Mode
is not available when the input source is set to
TV
.
✎
After connecting the game console, set
Game Mode
to
On
.
You may notice slightly reduced picture quality.
Caption
(On-Screen Text Dialogue)
■
Caption
: You can switch the caption function on or off. If
captions are not available, they will not be displayed on the
screen.
✎
The
Caption
feature does not work in
Component
or
HDMI
mode.
■
Caption Mode
: You can select the desired caption mode.
Default / CC1~CC4 / Text1~Text4
: (analog channels only) The
Analog Caption function operates in either analog TV channel
mode or when a signal is supplied from an external device to the
TV. (Depending on the broadcasting signal, the Analog Caption
function may or may not work with digital channels.)
Default / Service1~Service6 / CC1~CC4 / Text1~Text4
: (Digital
channels only) The Digital Captions function works with digital
channels.
✎
Service1~6
may not be available in digital caption mode
depending on the broadcast.
■
Digital Caption Options
: (Digital channels only)
Size
: Options include Default, Small, Standard and Large. The
default is Standard.
Font Style
: Options include Default and Styles 0 to 7. The default
is Style 0.
Foreground Color
: Options include Default, White, Black, Red,
Green, Blue, Yellow, Magenta and Cyan. You can change the color
of the letters. The default is White.
Background Color
: Options include Default, White, Black, Red,
Green, Blue, Yellow, Magenta and Cyan. You can change the
background color of the captions. The default is Black.
Foreground Opacity
: This adjusts the opacity of text. Options
include Default, Transparent, Translucent, Solid and Flashing.
Background Opacity
: This adjusts the opacity of the caption
background. Options include Default, Transparent, Translucent,
Solid and Flashing.
Return to Default
: This option sets each Size, Font Style,
Foreground Color, Background Color, Foreground Opacity and
Background Opacity to its default.
✎
Digital Caption Options
are available only when you can
select
Default
and
Service1 ~ Service6
in
Caption Mode
.
✎
The Foreground and Background cannot be set to the same
color.
Melody
Lets you control whether a melody plays when the TV is turned on
or off.
✎
The
Melody
does not play:
x
When no sound is output from the TV because the
MUTE
button
has been pressed.
x
When no sound is output from the TV because the volume has
been reduced to minimum with the
VOL –
button.
x
When the TV is turned off by the
Sleep Timer
function.
Auto Protection Time
■
Auto Protection Time (Off / 10 min / 20 min / 40 min / 1 hour)
: If
the screen remains idle with a still image for a certain period of time
you define, the screen saver is activated to prevent the formation of
ghost images on the screen.
Eco Solution
■
Energy Saving (Off / Low / Medium / High / Picture Off)
:
This adjust the brightness of the TV in order to reduce power
consumption. If you select
Picture Off
, the screen is turned off, but
the sound remains on. Press any button except the volume button
to turn on the screen.
■
Eco Sensor (Off / On)
: To enhance power savings, the picture
settings will automatically adapt to the light in the room.
✎
If you adjust
Cell Light
in the Picture menu, the
Eco Sensor
will be set to
Off
.
Min Cell Light
: When
Eco Sensor
is
On
, you can manually adjust
the minimum screen brightness.
✎
If
Eco Sensor
is
On
, the display brightness may change
(become slightly darker or brighter) depending on the light
intensity in your room. You can control the screen’s minimum
brightness with the
Min Cell Light
function.
■
No Signal Power Off (Off / 15 min. / 30 min. / 60 min.)
: Sets
how quickly the TV switches to standby mode, if no picture is
being received
.
✎
Disabled when the PC is in power saving mode.
■
Auto Power Off (Off / On)
: The TV will be automatically turned off
when no user operation is detected for 4 hours.
Support Menu
Self Diagnosis
■
Picture Test
: Use to check for picture problems. If the problem
appears in the test picture, select Yes and follow the directions on
the screen.
■
Sound Test
: Use the built-in melody sound to check for sound
problems. If the problem occurs during the test, select Yes and
follow the directions on the screen.
■
Signal Strength
: (Digital channels only) An HD channel’s reception
quality is either perfect or the channels are unavailable. Adjust your
antenna to increase signal strength.
■
Reset
: Reset all settings to the factory defaults.
✎
The PIN input screen appears before the setup screen.
✎
Enter your 4-digit PIN. Change the PIN using the
Change
PIN
option.
Software Upgrade
Software Upgrade
can be performed by downloading the latest
firmware from samsung.com to a USB memory device.
HD Connection Guide
Refer to this information when connecting external devices to the TV.
Contact Samsung
View this information when your TV does not work properly or when
you want to upgrade the software. You can find information regarding
our call centers and how to download products and software.
Media Play
Enjoy photos, music and/or movie files saved on a
USB Mass Storage Class (MSC) device.
P
POWER
MEDIA.P
❑
Connecting a USB Device
1.
Turn on your TV.
2.
Connect a USB device containing photo, music, and/or movie files
to the
USB
jack on the back of the TV. A pop up window appears.
3.
Press the
MEDIA.P
button on your remote. The Media Play menu
appears.
❑
Using the Media Play Menu
SUM
■
Change Device
E
Enter
R
Return
Media Play
Videos
To open Media Play in the Menu, follow these steps:
1.
Press the
MENU
button. Then, press the
▲
or
▼
button to select
Application
on the left, and then press the
ENTER
E
button.
Contact SAMSUNG WORLDWIDE
If you have any questions or comments relating to Samsung products, please contact the
SAMSUNG customer care center.
Country
CANADA
U.S.A.
Address
Samsung Electronics
Canada Inc., Customer
Service 55 Standish Court
Mississauga, Ontario L5R
4B2 Canada
Samsung Electronics
America, Inc.
85 Challenger Road
Ridgefield Park, NJ 07660
Customer Care Center
1-800-SAMSUNG(726-7864)
Web Site
www.samsung.com/ca
(English)
www.samsung.com/ca_fr
(French)
www.samsung.com
- 2 -
- 1 -
- 6 -
- 5 -
- 3 -
- 7 -
- 4 -
- 8 -
[PE533-ZA]BN68-04647A-ENG.indd 1
2012-08-07 �� 2:01:22
