Mortise
(SHS-AML320)
Strike
box
Strike
Mortise
(SHS-AML220)
Strike
Item
Specifications
Voltage
AA Alkaline 1.5 Batteries (LR6) 4EA or 8EA (6V)
Emergency Power
Source
9V Battery (6LF22) (Separately sold)
Operation Method Electronic Control Method
(Password entry or card or key tag reading)
Weight
3.9 kg (including both inner and outer bodies)
Product
Dimensions
Outer Body
(including the handle) 85mm(W) × 346.5mm(H) × 61mm(D)
Inner Body
(including the handle) 86mm(W) × 354.8mm(H) × 63 mm(D)
2
This function sets the time interval between the moment the door
open/closed sensor recognizes the door as closed and the moment
deadbolt locks the door. It can be prevented the deadbolt jam problem
by adjusting the time.
Default: 1 second
[51] : 1 second
[59] : 9 second
This section contains important information to ensure the user’s
safety and prevent potential damage to property. Please, read
this section carefully and use the product accordingly.
Warning
SHS-P717
64&3."/6"-
www.sds.samsung.com
Convenient Opening
Easy push/pull handle access
Welcome Function
When a user gets close to the door lock,
the authorization standby mode will
automatically activate.
Silent-Mode Function
When going in or out, the sound of the
key entering and door opening will be
suspended.
Automatic Card Reading Function
When a card touches the reader,
the reader will conveniently recognize the card.
Double Authorization
Requires card & password combination to open
Security Assurance Function
When someone is inside the house,
authorization for entry from the outside
will be prohibited.
Built-in Fire Detection
Generates alarm in case of a fire
Security Function
Prevents intrusion from the outside
GC68-02023A ED:04
6
5
4
3
Number Pad
Unlighted
Number Pad Lighted
Number Pad
Double Lock Light
Reset Switch
Safety Cautions
Outer Body Parts
• The user shall not install or repair the
product without authorization.
• Do not install the product in the place
where the gap between the door and the
frame is 5mm or more.
• Make sure that no unauthorized person
has the access to the password.
• Do not operate the product with wet
hands, and keep liquids such as water
or drinks away from the product, or
the product may malfunction or be
damaged.
• Do not use the excessive force or sharp
objects to push the lockbuttons, as this
can damage the product.
• Make sure that the door is completely
closed when going outside. The
manufacturer does not assume the
responsibility for any harm caused
by engagement of the lock on an
improperly closed door.
• Please do not hang on the product or
pull it.
• Be sure to correctly match the poles
(+/-) when installing the batteries. Install
the batteries with the correct poles (+/-).
• Replace all batteries immediately after
they run out of power, and never mix
new batteries with used ones.
• Do not use water, benzene or alcohol
when cleaning the product, as these
fluids can cause product malfunction.
• Replace the batteries within 1 week
after the battery replacement alarm
sounds.
10
11
9
8
7
12
Touch Number Pad
Card Reader
Proximity Sensor
Away Security
Setup
Emergency Alert
Light
External Power
Contact Part
Battery
Replacement
Time Alert
Entry Complete/
Silent Mode
Switch Button
Card and Key Tag Registration
Up to 30 cards, including the key tag and user password, can be
registered. (Only ISO14443 A Type is available.)
●
To register multiple cards or key tags, lightly place another card or key tag
to the card reader within 20 seconds after registering the previous card or
key tag.
●
ID number is given automatically in order of the registration.
Warning
Door Lock Time Setup Function
Alarm Sound (Prank Prevention Function)
This function generates an alarm sound and deactivates lock
operation when it is improperly handled from the outside.
Product Specifications
This function generates the alarm sound when fire is detected so that
the residence can quickly respond. The built-in fire detection function is
a basic function of the lock, and cannot be released by the user.
Fire detection function is operational at about 75
℃
± 10
℃
; this can
vary depending on the installation environment.
When fire occurs, the temperature sensor detects it and flashes the
[Close] button while generating the alarm sound.
The door is automatically opened after the alarm sound has stopped.
(The lock resumes normal operation if the inside temperature returns to
a normal level.)
The built-in fire detection function is activated when the temperature rises
around 60
°C
, which may differ depending on the installation environment.
Built-in Fire Detection Function
●
The contents of this user guide are subject to change without prior
notice to the user in order to enhance performance of the product.
Press [51] ~ [59] button, and then press
[
] button.
Open the battery cover of the
inner body and briefly press the
[Register] button.
Place the card or key tag to be
registered on the card reader of the outer
body. You will know the card or key tag
has been registered when “DING DONG
DENG” sounds.
Place the registered card or key
tag to the card reader on the outer
body.
3. Placing the Card or Key Tag on the
Card Reader (from the outside)
Enter the password when the
number pad is lighted, and press
the [
] button.
DING DONG
1. Pressing the [Register]
Button (from the inside)
2. Entering the Password
(from the outside)
DING DONG
DENG, DING
DING
DING DONG
DENG
4. Confirming Card or Key Tag
Registration (from the outside)
Press [Registration] button
briefly.
DING DONG
This alarm will sound if an attempt is made to open the door with an invalid
card, or if a wrong password is entered five times in a row.
The alarm sound is generated, and the lock is deactivated for 3 minutes. While
the door is in this inactive mode, a single “DING” sound is generated every 10
seconds and seven consecutive “DINGS” will sound after 3 minutes. Following
this, the lock is released from inactive mode.)
Press the [Register] button.
Outside
Apply the registered card or key tag to the card reader, or enter
the password and then press the [
] button.
Inside
Releasing the Alarm
Battery Cover
Auto/Manual
Locking Switch
1.5V AA Batteries
Registration Button
Inner Body Parts
Sound Control Switch
Built-in Wireless Module
(Optional)
CLOSE Button
The Battery Cover Release
Button
(After pressing the battery cover
release button, pull towards the
front, and then the battery cover
will open.)
Outer Body
The product components used may vary depending on the installation
environment.
Product Components
Inner Body
Key Tag (For B2C Only)
User Manual, Product Warranty
‘AA’ Batteries (LR6)
Emergency Key(5EA)
Handle Shaft Spring
Handle Shaft, Installation Screws
Installation Manual(For B2C Only)
Emergency
Keyhole
3. Entering a New Password
(from the outside)
DING DING
Enter the new password (4 to 12
digits) and press the [
] button.
Password Change
The password can be 4~12 digits number. Only one password can
be registered.
Enter the current password when the
number pad is lighted, and press the
[
] button.
DING DONG
1. Pressing the [Register] Button
(from the inside)
Press the [Register] button briefly.
2. Entering the Current Password
(from the outside)
DING DONG DENG,
DING DING
Setting the Security Function
This is a function to prevent any intrusion while you are out. Should
the door be opened from the inside while the intrusion prevention
function is on, the emergency alert light will flash and the alarm will
make “beep beep beep~” sound.
1. When the door is closed [ ] of the
outside body’s number pad will light up.
2. Press and hold the [ ] button on the
outer body for 3 seconds while the door
is locked.
Apply the registered card or key tag to
the card reader, or enter the password
and then press the
[
]
button.
DING DONG
DENG
Or
Setting the Security Function
Releasing the Security Function
Deletion
Use index number
All user password/card
Card or key tag
3S
Password
ID Number
88
CARD
Initialization
5S
4560852580
Other function
Double Authorization
Lock time
Welcome function
ON
ON
ON
No Alarm ON
OFF
OFF
OFF
5
7
9
4
6
1
2
3
1~9
Multi-leveled Security
Code
Direct registration of
Card or key tag
Card or user password
with ID number (01~30)
Registration
Password
New Password
ID Number
Changing password
CARD
CARD
Menu Table
Opening the Door from Outside with a Password
●
Password must be entered after the light is on, and if does not, touch
[Number Pad] and re-enter.
●
To cancel, press [ ] button and re-enter.
●
If the password is wrong 5 times, “peep” warning alarm will sound 20 times
and the system will shut-down for about 3 minutes. When malfunction
happens, “beep” will sound every 10 seconds, and stop mode will be turned
off automatically after 3 minutes with multiple ‘beeps’.
Note
When purchased, the product is set to Multi-leveled Security Code Entry
Mode initially. Please refer to “Multi-leveled Security Code Entry Mode
setting” for Common Mode setting.
※
Silent Mode
Before entering the password, press the [
] button and enter the
password, then both the sound of the key entering and the door opening
will be suspended. It is a useful function if you do not want to disturb
neighbors when you go in and out at night.
Touching [Number
Pad] will light up
the number pad.
When two arbitrary
buttons are lighted,
press the buttons
in order.
When the numbers on the
number pad are lighted, enter
the password and press the
[
] button.
Success:
DING DONG DENG
Fail:
DING DONG DING
DONG
The door can be opened from outside using a card or key tag.
Place the registered card or key tag on the card reader.
Opening the Door from Outside with a Card or
Key Tag
Success:
DING DONG DENG
Fail:
DING DONG DING
DONG
Placing the Card or Key Tag
on the Card Reader
Place the card or key tag on
the card reader.
The door will be opened after
1 second.
- If the security mode is changed as ‘common mode’, second step will be
skipped.
Closing the Door from the Inside
Automatic
Locking Setting
Manual
Locking Setting
The door is automatically locked 1 seconds after the door is
closed.
The door is locked when the
[Close] button is pressed.
●
To check if the door is locked from the inside, press the security button
briefly; the red LED will flash if the door is locked and the blue LED will blink
if the door is unlocked.
Note
~
Initialization (Password, Card, Key Tag)
All registered data (password, card, key tag) are deleted. After initialization,
the password is set to ‘1234’, and the registered card, key tag data are
erased. Please register a new password after initialization.
1. Pressing the [Register]
Button (from the inside)
2. Entering the Numbers for
Initialization (from the outside)
When the number pad is lighted, enter
‘4560852580’ and then press the [
] button.
Press and hold the [Register]
button for 5 seconds.
DING DONG
→
DING DING
→
DING DING
DING DING
Success: DING DONG DENG
Fail: DING DONG DING DONG
[Card and Key Tag Registration Without ID number]
Double Authorization Mode Setting
Double authorization mode requires both card and password to open
the door, ensuring more security.
To setup the double authorization mode, more than 1 card must be
registered.
Briefly press the [Register]
button on the inner body.
Press the [
] button after pressing the
[4] or [6] button, and the authorization
mode will be set.
[4] Button : Double authorization
mode on
[6] Button : Double authorization
mode off
Two-factor Authentication Mode Operation
Touching
[Number Pad].
Enter the password when
the number pad is lighted,
and press the [
] button.
Touch the card on to the [Card
Reader], if the authentication is
successful, the door will open.
Success:
DING DONG DENG
Fail: DING DONG
DING DONG
DING DONG
DING DONG
DENG
Success:
DING DONG DENG
Fail: DING DONG
DING DONG
[Card and user password registration with ID number]
3. Enter 2 digits ID number
4. Enter new user password
DING DONG
Input ID between 01 and 30, and
press [
].
DING DONG DENG
Enter new user password(4 to 12 digits)
and press [
].
4. Placing the Card or Key Tag
on the Card Reader (from the
outside)
5. Confirming Card or Key Tag
Registration (from the outside)
Place the card or key tag to be
registered on the card reader of the outer
body. You will know the card or key tag
has been registered when “DING DONG
DENG” sounds.
Place the registered card or key
tag to the card reader on the outer
body.
DING DONG
DENG
●
User password is only for the user, so other functions such as registering
cards are not available with this password.
●
One ID has only one password or card.
Warning
Multi-leveled Security Code Entry Mode Setting
You can set the security mode suitable for your use when you open
the door using a password.
Briefly press the [Register]
button on the inner body.
Press the [
] button after pressing the [7] or [9]
button, and the security mode will be set.
[7] Button : Multi-leveled Security
Code Entry Mode
[9] Button : Common Mode
DING
DONG
DING DONG
DENG
Sound Setting and Releasing
The sound that is generated when the number buttons are pressed,
when the door is locked or when the locked door is unlocked, can be
set according to the user’s preference. The product is set to generate
all sounds at the factory.
[0] : Mute [1] : Normal [2] : Loud
Open the battery
cover on the inner
body.
Put the [Sound Control]
switch on one of [0],
[1], or [2], and close the
battery cover.
DING DONG
DENG
Welcome Function On/Off
The welcome function is a convenient function that automatically
activates the authorization standby mode when a user approaches
the door, even before touching the number pad.
Open the battery cover and
press [Registration] button
briefly.
DING
DONG
On and Off / Function Description
- Welcome function : The mode will automatically activate the authorization
standby mode when a user approaches the door lock.
- One-minute alarm : When someone remains in frontof the door lock for
more than a minute, this mode will sound the tamper prevention alarm.
●
The factory defaults are set with the welcome function on and the alarm
function off.
●
The working distance of the infrared sensor can differ depending on light
conditions and other environments. When the front door is exposed to sun
light or constant bright lights it is advised to limit the usage of the sensor
as it might sound the alarm.
Caution
Code
Welcome
One-minute alarm
[1]+[
]
ON
ON
[2]+[
]
ON
OFF
[3]+[
]
OFF
OFF
Replacing the Batteries
If the melody of “Blues for Elise” sounds when opening the door with the
password or a card (key tag), it is time to replace the batteries.
(The low battery indicator is lighted when the melody sounds.)
Battery Replacement Alarm Generation
Replace all 8 batteries within a 1 week of the first alarm sound.
- The unit will stop operating suddenly if the batteries are not replaced.
Replacing the Battery
●
Depending on battery manufacturer, date of manufacture and the user
environment, the duration of use may vary.
(In the case of average use, given as 10 times a day, 8 AA alkaline
1.5Vbatteries can last for 12 months.)
●
If the poles of the batteries are not placed properly, the lock will not operate
normally.
●
Liquid leaks from batteries can damage the product. Check the batteries
regularly (every 6 months).
●
After the battery replacement alarm has sounded, password/card
information cannot be registered, changed, deleted, initialized or configured
until the batteries are replaced.
Warning
Intrusion Detection Function
This function generates the alarm sound when an attempt is made to
forcefully open the door from the inside or the outside.
(This is a basic function of the lock, and cannot be separately set or
released.)
If the door is forcefully opened while locked, the door opening sensor
detects it and generates the alarm sound.
~
Automatic/Manual Locking Setting
The Automatic Locking mode allows for automatic locking of the door when
it is closed.
- Automatic: The door is automatically locked 2 seconds after being closed.
- Manual: The door does not lock automatically, and [CLOSE] button must be
pressed from the inside, touch [Number Pad] to close the door.
Set the [Automatic/Manual
Locking] toggle switch of
the Inner Body to the ‘A’/‘M’
position.
Open the
battery cover
on the inner
body.
~
Using the Emergency Battery
If the batteries are not replaced after their replacement time comes, they will
be completely discharged and the lock will not operate.
Place the card or key tag on the card reader, or enter the password, while the
9V battery is connected to the external power port of the outer body.
Purchase an emergency battery (9V) at the nearest store.
- As the alkaline batteries offer longer life, they are recommended over
the manganese batteries or rechargeable ones.
Opening the Door Using an Emergency Battery
Or
Mortise
Deadbolt
Latch bolt
Open-door sensor
SHS-AML320
SHS-AML220
Opening by Pulling the Inner Handle
Opening the Door from the Inside
Warning
●
Please be careful not to trap your
hand during use.
●
Manage your password with care so that unauthorized people will not have
access to it. Regularly changing your password can reduce the risk of it
being leaked.
Warning
~
~
While the door is locked, press [Security
Assurance] button on the inner body
part for 3 seconds.
Pull the inner body
handle to open the door,
and it will deactivate.
DING DONG
DENG
DING DONG
DENG DONG
Security Assurance Mode
Activation
Security Assurance Mode Operation
Rapid beeping
●
When the security assurance function is activated, the door cannot be
unlocked from the outside, so please be careful. Be especially careful not
to allow children to set this mode accidently from the inside.
Warning
Or
Security Assurance Mode Activation/Deactivation
At-home security mode is to prevent opening of the door from outside
while someone is inside.
Inside: Press the [Security Assurance] button, then the
sound for action-unavailable willbe heard.
Outside: Press the [Number Pad] or touch with a card,
then the sound for action-unavailable will
be heard.
~
Security Assurance Mode
Deactivation
To make sure the password has been
properly registered, check the new
password and close the door.
4. Checking New Password
Operation (from the outside)
Deleting Registered Cards
You can delete individual or all registered cards.
1. Pressing the [Register]
Button (from the inside)
Press the [Registration]
button for 3 seconds.
Enter the current password when the
number pad is lighted, and press [
]
button.
2. Entering the Current Password
(from the outside)
DING DONG
DENG, DING DING
[Deleting Cards]
3. Reading the card to be deleted
If you want to delete all cards data, press
[88] + [
] after step 2.
DING DONG
DENG
DING DONG
DING DING
[Deleting ID information]
3. Enter ID number to delete
Enter 2 digits ID number, then the
card or user password of it will be
deleted.
DING DONG
DENG
