2
BIOMETRICS
GC68-02024A ED:01
BIOMETRICS
SHS-P910
Instruction Manual
4
3
Number Keypad
Turned Off
External Power Contact Area
Precautions for safety protect the user's safety and prevent damages
and inconvenience due to accidents. Please read this and use the
product properly.
Warning
●
Do not install or repair the product
randomly as you want.
●
Do not install the product in a location
where the gap between the door and
doorframe is more than 5mm.
●
Cautiously manage the passcode so
that other people cannot know it, and
regularly change the number.
●
Do not operate the product when your
hand is wet, and be careful to not let
water, beverages, and other liquid to
get inside the product.
●
Do not forcibly press or use a sharp
tool to hit the but ton.
●
When you are going out, always
check the ensure that the door was
fully locked.
●
Properly fit the battery into the product
onto its accurate (+/-) terminals.
When the battery is incorrectly placed
in its direction or charge as displayed
into the battery room, leakage and
breakage may occur, so please be
careful.
●
When the battery life is ended, replace
all the batteries at once, and avoid
using new and used bat teries at the
same time.
●
When cleaning the product, do not
wipe it with water, benzene, or
alcohol, and instead, use a dry cloth.
●
Replace the batteries to new ones
within one week of first hearing the
battery replacement notification alarm.
Product components may be changed depending on the
installation environment.
Mortise
Precautions for Safety
Names and Features (Outside)
Product Components
Outside of Main Unit
Strike
(FOR B2C ONLY)
Strike box
Inside of Main Unit
Key Tag 2E A(FOR B2C ONLY)
Manual, Emergency key
‘AA’Battery (LR6)
Fixation spring for handle shaft
Handle shaft, installation screw
Installation map(FOR B2C ONLY)
BIOMETRICS
BIOMETRICS
Number Keypad
Touch
Number Keypad
Turned On
Card
Recognition Area
Proximity sensor
area
Number key pad
Crime prevention
feature
Dual locking lamp
Reset button
Finish button
turn on “MANNER MODE”
Battery exchage
alarm
Names and Features (Intside)
Battery cover opening button
(To open the battery cover,
press the battery cover open button
and pull forward the cover.)
1.5V A A battery
Volume control swich
Mounting with wireless
module (optional)
Automatic/Manual
lock switch
Battery cover
Registration button
Relieve button
Names and Features (Mortise)
●
Passcode must be enter ed when the number k eypad islighted up, so
if the lights ar e not on, then touch the [number keypad] and then
re-enter the passcode.
●
When the passcode is incorr ectly entered to cancel the input, press the
[ ] but ton and star t from the beginning.
●
If the passcode is incorrectly entered for five times in a row, alarm sound
is played 20 times and the operation of doorlock is paused for 3 minutes.
During the operation pause status, "dding" sound is played every 10
seconds and after 3 minutes a long "dding" sound is played. And then
the pause status is automatically disabled.
Reference
When the product is purchased, it is set up as the dual
security mode. If you want to change to the normal mode,
refer to 'Dual security mode setting'.
※ Manner Mode
The sound of pressing key button or door opening does not come out if you
press [*] button first before entering passcode.
This function is useful when you enter home silently at night.
Open the locked door from the outside with fingerprints.
Please correctly contact the registered fingerprint to the fingerprint recognition area.
Success:↑DingDongDengDong
Fall: DingDongDingDong
1. Press [Fingerprint Cover Open]
button.
When the [Fingerprint Cover Open]
button is pressed, fingerprint
recognition cover opens.
Opening the door from the outside
(Fingerprint)
2. Fingerprint is recognized.
When LED light of the fingerprint recognition
panel is on, contact your fingerprint.
After 1 second, the cover of the fingerprint
recognition site is closed. Now you can open
the door by pushing the doorlock handle.
Opening a door from inside
Opening a door
by pushing the inner knob
●
Be careful of jamming your hand in use.
Caution
Closing a door from indoor
When setting the
automatic lock
When setting the
manual lock
The door will be locked automatically
after closing the door.
The door will be locked
when pressing [Relieve]
button or [Open] button on
the remote control.
●
In the case of you want to check if the door is locked at home, push the
relieve button shortly. If the door is locked, red LED light will be on.
Otherwise, you will see blue LED light is on.
Reference
Using the remote control
(option)
Use the wireless wall pad
(optional)
Press the [OPEN] button on the
remote control.
When pressing the [Door Open] button
of the wireless wall pad, the locked
status is released.
(It may vary depending on the wireless wall
pad models.)
Or
Maximum of 100 fingerprints can be registered for use.
1. Press the
[Registration] button
2. Recognizing the fingerprint that will
be registered
3. Registration complete
After opening the battery
cover of the inside main part,
press the [Registration] button
briefly.
When the LED of fingerprint recognition area is
lighted up, contact the fingerprint that will be
registered. When the LED is turned off, lift the finger.
(Total of 3 authentications)
Press the [Fingerprint Cover Open] button on the
outside body to open the fingerprint recognition area
cover and contact the fingerprint to the fingerprint
recognition area.
Fingerprint Registration
4. Confirming on registration
Opening the door from the outside
(passcode)
Fingerprint cover open button
Fingerprint recognition cover
Dead bolt
Latch bolt
Door open sensor
To complete the fingerprint
registration, press the
[Fingerprint Cover Open]
button to close the cover.
BIOMETRICS
Dingdong
Success :
DingDongDeng
Fail :
DingDongDingDong
DDing
You must carry or keep at least one
emergency key outside.
Insert for spare key
Bottom part of body outer part
●
To prevent theft accidents, it is recommended to use the passcode that
is 6 digits or longer (only 0~9 number s are usable).
●
Please be careful to manage the passcode so that other people will not
know. Using the same passcode for a long period of time ma y lead to
its exposure, so regularly change the passcode for use.
●
Registered passcode cannot be deleted, so r egister a new passcode to
use.
Caution
Passcode can be registered in 4~12 digits, and only one can
be registered to use.
1. Press the [Register]
button.
2. Register the new passcode.
Insert the passcode(4~12digits)
that you want to register, then
press [*] button.
Open the battery cover and
shortly press [register] button.
Dingdong
DingDongDeng
Passcode Registration
※Registration/setting only works under the condition of door is open.
Initialization(password, card, key tag, remote controller)
2. Insert initialization number
1. [registration]press button
open a battery cover
press [registration]button
for 3seconds.
Dingdong
→
DDingDDing
Open the door from outside by using a card and a key tag.
Correctly place the card or the key tag that registered on the
card recognition section.
Placing a card
The door will be open if you wait 1
second after placing a card or a key
tag on the card recognition section.
●
If card key and key tag is not automatically recognized by doorlock, touch
the key pad and try again. The door will open.
Reference
BIOMETRICS
Opening the door from the outside
(card, key tag)
5
6
Insert passcode first, then press [*] button.
2. Normal Mode
When touching [number pad],
the light is on the number pad.
Success: ↑DingDongDengDong
Fall: DingDongDingDong
BIOMETRICS
Convenient Opening of the Door
Simple PUSH PULL motion
Welcome Feature
When user approaches to the
doorlock, its status is automatically
changed to standby for recognition
Manner Feature
Temporarily blocking the sound of
pressing key buttons and opening
door when going in and out
Automatic Card Recognition Feature
Easily open the door by card key
Dual-Authentication Feature
Dual-Authentication Feature with
fingerprints and passcode
Dual lock Feature
Automatically blocking every recognition attempt
when the owner is at home.
Fire Detection Feature
Built-in fire detection sensor
Crime Prevention Feature
When going out and at the attempt of criming,
prevention alarm will be on.
When touching
[number pad], the
light is on the
number pad.
1. Dual-security mode
Two buttons randomly
lit up, so press the two
numbers in the
sequence.
When all of the lights in the
number keypad show up, enter
the passcode and press [*]
button.
Success: ↑DingDongDengDong
Fall: DingDongDingDong
Dingdong
Success :
↑
DingDongDeng
Fail :
DingDongDingDong
Warning
Success :
↑
DingDongDeng
Fail :
DingDongDingDong
Relieve
Re-enter the
Door is locked
Door was opened
Remove all the information stored. Once it is initialized,
password will be set as '1234'.Your need to register your
card and a password again after its initialization.
Dingdongonce
lights up on number pad,
press '4560852580' then [*]
- sucess: Dingdongdang
- Fail: Dingdong Dingdongonce
