This manual describes the configuration of the Wireless Enterprise
WEA512i and its installation procedures.
WEA512i (Indoor) Quick Installation Manual
Introduction
What is the WEA512i?
The Samsung WEA512i is an Access Point (AP) which has been designed for the
wireless communications optimized for indoor hotspot environment.
It offers unparalleled performance and connectives for all wireless devices such as
smartphones, laptops, tablets etc.
The WEA512i supports the following features:
- IEEE 802.11a/b/g/n/ac standard
- PoE (Power over Ethernet) IEEE 802.3af
- 2 × 2 MU-MIMO (Multi User-Multiple Input Multiple Output)
- Wireless LAN through both 2.4 GHz and 5 GHz bandwidth simultaneously
Components
After unpacking the WEA512i, check whether all of the following components
are included.
WEA512i
Package Contents
Mounting Bracket
5 M3 × L6 screws
(Including 1 spare)
Installation Manual
Security Torx (T10) Screw
Plastic 4 anchors
4 M4 × L28 screws
- It is recommended to keep all packaging materials and the box.
- The power adapter is sold separately. When necessary, please contact
the place of purchase.
Functions
Front View
Status LED
Rear View
DC Input
Ethernet Port (PoE)
Factory Reset Switch
Console Port
A dust cover is installed on DC Input port (DC 48 V).
Remove the cover before use.
Interface
Port Name
Description
Status LED
Displays the status information of the WEA512i via LED.
DC Input
This is for connecting the power adapter when the PoE is not
available.
Ethernet Port
(PoE)
Supports 1000 BASE-T Gigabit Ethernet and PoE IEEE 802.3af.
Console Port
This is used for checking the operational status of the WEA512i
and for CLI input.
Factory Reset
Switch
This is used to reset the WEA512i to the initial factory settings.
Status LED
LED
Status
Description
System start
status
White On
Initial LED status
Blue On
Device reset and test in progress
Red On
Booting failure (Device reset failure)
Normal
operation status
Green On
When there is no connected wireless UE
Blue On
When there is a connected wireless UE
Upgrade
Green blinking
Software upgrade in progress
Error status
Red blinking
Physical connection error of network
Yellow blinking
IP address conflict
Purple blinking
Dynamic IP address allocation failure
Bluish-green blinking Logical connection error of network
Red, green and off
repeated
Wireless interface error
Installation
The WEA512i can be installed on ceilings or walls.
Please check whether all the components are included before installation.
Before Installation
Safety Requirements
Risks may be caused when the following safety warnings are not properly observed.
For safe use, make sure to be well-informed.
- There is an electrical risk with the product. Make sure
that the power is off during installation and do not
proceed with the installation when there is current
leakage. Use of products with current leakage may
cause serious electrical shock to the user.
- Wear anti-static gloves or take appropriate actions to
prevent ESD when handling the product.
- The wired LAN hub providing power over the Ethernet
(PoE) in accordance with IEEE 802-3af/at shall be a UL
Listed device with the output evaluated as a Limited
Power Source as defined in IEC/EN/UL60950-1.
- This product must be installed or removed only by appropriately-trained
service personnel.
- All interconnecting equipment including this product must be installed
within the same building. For details, refer to Environment A of IEEE
802.3af/at standard.
- This product must be installed with at least 3 m or more distance from the
WiMAX/3G/4G repeater or antenna.
Installation Instructions
The instructions below must be followed when installing.
- It must be installed in a place that can be easily accessed for product installation,
cable connection and maintenance.
- The PoE LAN cable must be always installed away from any electrical interference
source such as power lines, fluorescent lights or transmitters.
- The PoE LAN cable must be CAT 5E or higher.
- When PoE is unavailable, a power adapter (sold separately) can be used. The 3-pin
(including ground) power socket that supplies 100~240 V AC, 50~60 Hz must be
located within 2 m from each equipment and the power must be supplied through an
independent circuit breaker. It is recommended to use the equipment that uses a filter
or a surge protector.
Installation on Ceilings (When the ceiling type is T-bar)
- When incorrectly installed on the ceiling, the WEA512i may drop onto a
person or equipment. Therefore, make sure to fix it firmly.
- If the ceiling type is not T-Bar, please refer to the ‘Installation Manual’
provided separately. For this installation manual, please contact the
dealer.
1.
Remove the holding tape that was attached to fix the ceiling clip.
Holding tape
