background image

COUNTER/TIMER    CNT-700 MANUAL 

Thank  you  for  your  purchase of  our  Counter/Timer  CNT-700  series.  Please  read  this  manual carefully and 

understand  totally  before  use  this  device.  This  manual  contains  important  information  to  use  safely  for  this 

product.   

1)

 

Symbols and meaning   

  The following symbol is very important to use this device safely. Please be sure to handling to carefully this 

manual of this symbol. 

!

        (

Warning

)

 

 

This devices dose not verify as safety devices, when you use together with dangerous devices, so please use 

after install 2

nd

 safety device before this devices. 

 

(

Danger

)

 

 

electric shock   

 Never touch the AC terminal with bare or wet  hand during power on. It may cause electric 

shock. 

Please make sure turn off power when you check power line . 

 

!

 

    (

Caution

)

   

1.

 

Please use over M 3.5, width max 7.2m terminal wire for AC power line. 

 
2.

 

Do not use without manufacture recommended application, it may cause damage of body or broken 

of product.   

 

 
3.

 

Please  prevent  the  dust,  water,  oil  and  debris  of  wire  into  the  devices.  It  may  cause  the  fire  or 

damage of products. 

 
4.

 

Do not disassemble or convert or remodel without permission from manufacture. it may cause error 

and cannot guarantee the quality. 

 

 
5.

 

Please be sure making wire separately with power line to reduce inducts noise. 

 
 

6. Please install the switch or circuit Breaker to protect from over voltage. 
 
7. Please be sure make wire separately with signal line and power line to reduce induct noise   
 
8. Please  do  not  install  the  devices  near high  frequency  noise  generating  devices (likes  high  frequency 

welding M/C, high capacity SCR controller, Inverter, etc.) 

 

 

The above mentioned note is can make error to devices. 

 

Please be sure for follow as described at manual. 

 

 

 

 

Summary of Contents for CNT-700






















Reviews: