Fig 3
ASSEMBLY OF THE TREE
1. Locate the bottom section of the tree which is identified
by a label on the outer branches marked “A” (Fig 5).
2. Remove the protective plastic cap by twisting and pulling
it from the end of the pole, (that is pinched to a point), and
place the end into the tree stand. Be sure the pointed end
of the pole extends to the bottom end of the stand.
3. Now tighten the eyebolts evenly on the tree stand; being
careful not to over-tighten (Fig 3).
ASSEMBLY INSTRUCTIONS
(We recommend wearing proper clothing in order to prevent
scratches that may occur during the assembly process.)
Carefully unpack the contents from the tree’s carton (Fig 1);
including the contents of the poly-bag that is adhered to the
interior flap of the tree’s carton.
Contained in the poly-bag are LED replacement bulbs and a
remote control which operates your tree’s 7 function lighting
capability.
Your tree should include the following components:
A folding metal tree stand with (3) eyebolts.
An ON/OFF push button foot pedal with cord and plug (Fig 6);
which is pre-attached at the lowest section of your tree (Fig 5).
The 5’ tree will have (2) tree sections. The 6.5’ and 7.5’ trees will
have (3) tree sections; (“A”, “B” and “C”; as shown in Fig 5).
The 9’ tree will have (4) tree sections “A”, “B”, “C” and “D”.
Thank you for your purchase of this pre-lit & pre-shaped
Christmas tree.
With proper use and care, this tree will provide years of
trouble-free enjoyment.
Please follow the instructions below in order to effectively
assemble and disassemble your tree.
In the event that you should encounter any issues during
the assembly of your tree; please refer to the
“Troubleshooting” portion of this manual or call our toll free
customer service number at 1-888-831-6656, and a trained
representative will assist you.
Customer service hours of operation:
Monday-Friday: 8:00am – 4:30pm CST.
Holiday weekends:
Last weekend in November: 8:00am – 4:30pm CST.
First weekend in December: 8:00am – 4:30pm CST.
Visit us on the web at www.santasbest.com
PRE-LIT & PRE-SHAPED CHRISTMAS TREE
ASSEMBLY OF THE TREE STAND
1. Remove the tree stand from the plastic bag, loosen the eye
bolt and open the tree stand to form an “X”.
2. Align the holes for the insertion of the remaining (2)
eyebolts.
3. Insert each eyebolt and begin threading in a clockwise
direction for a couple of rotations only; leaving enough
room for the tree’s pole from section “A” to be inserted into
the assembled stand (Fig 2).
4. Place the tree stand in its desired location; as once the tree is
fully assembled, it may be too difficult to move and relocate.
4. Carefully cut the nylon strapping bounding the branches
upright.
CAUTION: Be extremely careful not to cut any of the exposed
light set wires.
5. Now gently guide the branches downward into place.
6. Beneath the canopy of section “A”, contains an push button
foot pedal with cord and plug (Fig 6).
Remove the twist-tie binding the cord together and insert
the plug into a working electrical outlet.
7. On/off push button foot pedal operation:
The on/off push button foot pedal is intended to provide
basic manual on/off operation only; and therefore cannot
provide the remote control’s 7 function lighting capability.
Riverwoods, IL 60015 USA
www.santasbest.com
2. If failure to light persists, press the push button foot pedal; as it
may be in the “Off” mode.
3. If the top of the tree or another individual lettered section does
not illuminate, remove each section and then reinsert as
instructed, to ensure the electrical connection is made.
NOTE: The tree’s top is designed specifically for a secure and
firm connection point. Downward force will be needed to
ensure that the electrical connection occurs.
4. Always inspect your tree for any burned out LED bulbs.
Although the tree will continue to remain lit even if a bulb
burns out, is loose or is missing; any burned out LED bulbs
should be replaced promptly to ensure the performance and
life expectancy of your tree.
5. If lighting is out of sequence after replacing an LED, remove
and re-insert the LED making sure to align the husk tabs as
illustrated in the safety instruction sheets. This is a specialty
bulb. Do not replace with a standard LED or Incandescent bulb.
Should you need additional bulbs please call our customer
service department at 1-888-831-6656.
Made in China Printed in China
This is not a toy, for decorative use only.
NOTE: DO NOT USE A DIMMER SWITCH, INSTALL ANY
ADDITIONAL LIGHTING OR ORNAMENTION THAT IS
POWERED THROUGH THE LIGHT BULB SOCKETS. DOING
THIS MAY RESULT IN DAMAGE TO THE LIGHTING SYSTEM
OR MAY CAUSE PERSONAL INJURY; THEREFORE VOIDING
THE LIMITED WARRANTY PROVIDED WITH THIS PRODUCT.
1. Gently remove the plug from its electrical outlet, and carefully bind
the cord which contains the push button foot pedal and plug.
2. Beginning with the tree’s top section; lift each section straight
up from the section below, and continue working downward.
NOTE: You may have to slightly wiggle each section as you lift
each section upward.
3. To remove the bottom and final section; loosen the eyebolts by
turning in a counter-clockwise direction and lift section “A”
from the support collar of the tree stand.
4. Gently fold the branches of each section upward, towards the
center, and position in the storage container.
NOTE: With the exception of the tree’s “top” section; by holding
each section upside down; the branches will collapse down-
ward, due to the hinging, aiding in the packing of each section
into the storage container.
5. Fully unthread the eyebolts from the tree’s stand and fold
together; placing in the storage container.
6. It is recommended to always store the tree in a cool, dry
location protected from excessive exposure to heat or sunlight.
NOTE: Store your remote control in a SAFE & DRY location and
remove the battery from remote control before storage.
DISASSEMBLY & STORAGE
NOTE: ALTHOUGH THE LED LIGHT STRINGS ON THE TREE ARE
RATED FOR INDOOR OR OUTDOOR USE; THE COMBINATION
OF THE TREE WITH THE LED LIGHTS IS RECOMMENDED FOR
INDOOR USE ONLY.
Fig 2
10. Once section “B” is fully inserted downward into section “A”;
both section “A” and section “B” will now be lit.
11. Again, carefully cut the nylon strapping bounding the
branches upright; being extremely careful not to cut any of
the exposed light set wires.
12. Now gently guide the branches of section “B” downward
into place.
13. Depending on the height of the tree you have purchased,
you will continue to build your tree upwards, section by
section, following the above steps until the tree is
completely assembled. Each section of the tree is labeled in
alphabetical order beginning from the bottom to the top.
8. Locate the next section of the tree which is identified by a
label on the outer branches marked “B” (Fig 5).
9. Remove the protective plastic cap by twisting and pulling it
from the end of the pole on section “B”; insert that end onto
the top of the pole of section “A” (Fig 4).
Fig 4
EZ-POWER™ TECHNOLOGY
NOTE: Your tree has been designed with EZ-Power™
technology; allowing for each of the tree’s remaining
sections to light up automatically, upon a firm insertion of
each lettered section (Fig 5).
CCT15
Patent No. : RE43,890E, 8,836,224 and other patents pending.
Fig 6
• Steady Multi
• Steady White
• Steady Pastel
• Slow Fade White to Multi
• Flash White to Multi
• Slow Twinkle
• Fast Twinkle
REMOTE CONTROL OPERATION
Contained in the poly-bag; which is adhered to the interior flap
of the tree’s carton, is your remote control that operates your
tree’s 7 lighting functions.
Before operation; a standard 9 volt type battery (6F22, 6LR61 or
23F6-220) must be installed into the remote control; by simply
removing the slide plate located on the back of the remote
control.
The remote controls the
following 7 functions as well as
the ON/OFF operation. To change
the functions, simply press the
“Function ” or “Function ” to
cycle through each function.
NOTE: If the tree is powered off by
the use of the push button foot
pedal, remote control or by
unplugging it from the electrical
outlet; when powered back on the
tree will resume the memory of
the last lighting function selected.
TROUBLESHOOTING
1. If the tree does not illuminate press the function button on
your remote control. If failure to light persists the battery may
need to be replaced. Insert a standard 9 volt type battery (6F22,
6LR61 or 23F6-220); aligning the appropriate ( +/- ) markings
accordingly.
NOTE: The tree’s 7 function lighting capability is controlled
solely by the use of the remote control provided.
If the tree fails to light due to a damaged or defective remote
control; please resort to manual push button foot pedal
operation until a new remote control can be provided through
our customer service center.
Fig 1
A
B
C
Foot Pedal
Fig 5
18”
2015 QVC
Heritage Spruce Instruction Sheet - 7 Function Remote (English)
Date: 5/27/15
15”
Item # 7245015-IP66QV (7.5ft Heritage Spruce)
7245016-IP66QV (5ft Heritage Spruce)
7245017-IP66QV (6.5ft Heritage Spruce)
7245018-IP66QV (9ft Heritage Spruce)
