background image

 15G0851Q1 

 

DATA LOGGER 

ES851 

 

 

 

 

BASIC – ADVANCED 

USER MANUAL 

-Programming Instructions- 

 

 

 
Issued on 23/01/09 

R. 02 

Ver. 1.67x 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Elettronica Santerno S.p.A. 

Strada Statale Selice,  47 – 40026 Imola (BO) Italy 

Tel. +39 0542 489711 -  Fax +39 0542 489722 

 

 

 This manual is integrant and essential to the product. Carefully read the instructions contained herein as they 

provide important hints for use and maintenance safety. 

 This device is to be used only for the purposes it has been designed to. Other uses should be considered improper 

and dangerous. The manufacturer is not responsible for possible damages caused by improper, erroneous and 

irrational uses. 

 Elettronica Santerno is responsible for the device in its original setting. 

 Any changes to the structure or operating cycle of the device must be performed or authorized by the Engineering 

Department of Elettronica Santerno. 

 Elettronica Santerno assumes no responsibility for the consequences resulting by the use of non-original spare-

parts. 

 Elettronica Santerno reserves the right to make any technical changes to this manual and to the device without prior 

notice. If printing errors or similar are detected, the corrections will be included in the new releases of the manual. 

 Elettronica Santerno is responsible for the information contained in the original version of the Italian manual. 

 The information contained herein is the property of Elettronica Santerno and cannot be reproduced. Elettronica 

Santerno enforces its rights on the drawings and catalogues according to the law. 

E n g l i s h

 

Summary of Contents for ES851





















Reviews: