background image

Sanuvox Technologies Inc, © 2020 All rights reserved. August 2020 EN v.4

Instruction Manual

Photos illustrating products are non contractual.

SANUVAIR

®

 S100

AIR PURIFICATION UNIT

Commercial Model

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE SAFETY INSTRUCTIONS BEFORE USING THIS PRODUCT.

Read and follow all instructions contained in 

this manual before using the product. Failure 

to comply with these instructions may result 

in personal injuries or damage to the unit or 

system.

1.  Installation and servicing of air conditioning 

and related equipment can be hazardous due 

to systems pressure and electrical components. 

Only trained and qualified service personnel

 

should install, repair or service equipment.

2.  Untrained personnel can perform basic 

maintenance functions such as replacing 

lamp(s)  and/or  filter(s).  All  other  operations 

should be performed by trained service 

personnel.

3.  When working on the unit or system, observe 

precautions in the literature, tags and labels 

attached to the unit or system, and all other 

safety precautions considered as best practices 

in the HVAC industry.

4. When applicable, local regulation may 

comprise more restrictive installation and/or 

certification requirements. The afore mentioned 

requirements prevail on those of this document 

and the installer agrees to conform to these at 

his own expense.

5.  Follow all the safety instructions outlined in this 

document and respect all local and national 

codes applicable.

6.  Never expose eyes or skin to ultraviolet light 

from any source.

 Therefore, 

before installing 

or performing maintenance on the unit or 

system,  TURN OFF AND DISCONNECT the 

unit or system from all power sources (there 

may be more than one switch to disconnect).

 

 CAUTION: Electrical shock may cause 

personal injuries or possibly death.

7.  UV  rays  may  destroy  certain  types  of  filters 

(polymer or plastic); please keep the unit or 

system light away from shining directly on 

plastic.

8.  When installing or performing maintenance on 

the UV unit or system, it is recommended to 

wear safety glasses and gloves. In order to 

avoid reduced performance of lamp(s), do not 

touch lamp glass without gloves.

9.  UV lamps contain a small quantity of mercury: 

if a lamp breaks, clean and dispose of with 

care. UV lamps can be disposed/recycled after 

use,  as  any  other  fluorescent  lamps.  Contact 

and  follow  your  local  and  national  authorities’ 

specific instructions.

10. 

Use  only  specified  SANUVOX  branded 

replacement UV lamps with your unit or 

system. Use of any other lamps will void your 

warranty and can result in damage to the unit, 

system and/or lamp(s).

11. Most UV units or systems are not waterproof. 

DO NOT INSTALL OUTDOORS unless 

specified otherwise.

SAVE THESE INSTRUCTIONS

Installation Date:  _______________   Installed by:  _________________
Installer Contact Info.:  _________________________________________

REGISTER 

YOUR WARRANTY

 

ONLINE AT 

www.sanuvox.com

Summary of Contents for SANUVAIR S100













Reviews: