background image

07-01955E F479-230V/78-006 AU 

Legend Brands, Inc. 

Owner’s Manual 

HVE3000 Flood Pumper and Inline Booster  

F479-230V AU 

LEGEND BRANDS, INC.

 

15180 Josh Wilson Road, Burlington, WA 98233, USA 

Phone: +1 360-757-7776  Fax: +1 360-757-7950

 

 

international.legendbrands.net

  

The high-efficiency HVE3000 can be used both as a flood pumper to quickly remove excess 
liquid water for flood remediation and as an inline truckmount booster to extend the 
effective vacuum hose length for carpet extraction and cleaning.  

Patents

http://www.LBpatents.com

 

R E A D   A N D   S A V E   T H E S E   I N S T R U C T I O N S

 

SAFETY INSTRUCTIONS 

 

 

 

 

 

WARNING! Do not alter or modify your HVE3000 in 
any way. Use only replacement parts authorized by 
Legend Brands, Inc. Modifications or use of 
unapproved parts could create a hazard and will 
void your warranty. Contact your authorized Dri-Eaz 
or Sapphire distributor for assistance. 
 
WARNING! Electric shock hazard, vacuum impeller, 
and hot surface hazards.  

Do not leave appliance when plugged in. Unplug from 
outlet when not in use and before servicing. 

Do not allow to be used as a toy. Close attention is 
necessary when used by or near children. 

Do not pull or carry by cord, use a cord as a handle, 
close a door on a cord, or pull a cord around sharp 
edges or corners. Do not run appliance over cord. Keep 
cord away from heated surfaces.  

Do not unplug by pulling on cord. To unplug, grasp the 
plug, not the cord. 

Do not handle plug or appliance with wet hands. 

Do not put any object into openings. Do not use with any 
opening blocked; keep free of dust, lint, hair, and 
anything that may reduce air flow. 

Turn off all controls before unplugging. 

Use extra care when cleaning on stairs. 

Do not use to pick up flammable or combustible liquids, 
such as gasoline, or use in areas where they may be 
present. 

Connect to properly grounded outlet only. See 
Grounding Instructions. 

To reduce the risk of fire and electric shock due to 
internal component damage, use only VersaClean 
cleaning fluids intended for use with this appliance.  

Use indoors only. 

WARNING

 

PROTECT YOUR EQUIPMENT 

To protect your valuable equipment and prevent voiding the warranty, read and follow these instructions:  

 

Install the HEPA filter when using the unit on Category 3 restoration jobs.  

 

Remove and discard filter at the end of the all Category 3 restoration jobs. Hearing protection is recommended. 

 

Use defoaming chemicals whenever foam is present in waste tank.   

 

Replace the HEPA filter if it gets wet during operation.  

 

If foam/water is pulled through the vacuum blower, remove hose/wand and run blower unit for 5 minutes to dry 
out the system prior to storing. 

Failure to follow these instructions can damage the vacuum system. 

Maintenance 

 

Replace vacuum blower brushes after 800 hours of operation.  

Summary of Contents for Dri-Eaz HVE3000










Reviews: