background image

2

Introduction 

Table of Contents

Thank you for your purchase of the SATO Rewinder RWG500. 

This manual helps first time users understand the basics of the 

RWG500 in a short period of time. 

To get the most out of the functions of the RWG500, make sure 

to read this manual carefully. 

Safety Precautions · · · · · · · · · · · · · · · · · · · · · · ·  3

Main Body and Accessories · · · · · · · · · · · · · · · · · ·  6

Parts Identification · · · · · · · · · · · · · · · · · · · · · · ·  7

Joint plate setting · · · · · · · · · · · · · · · · · · · · · · · ·     9

First Roller Height Setting  · · · · · · · · · · · · · · · · · ·  14

Connection to Printer    · · · · · · · · · · · · · · · · · · · ·  15

Label Setting

 

Rewinding Direction  · · · · · · · · · · · · · · · · · · · ·  18

 

Rewinding Shaft

      

Direct Rewinding    · · · · · · · · · · · · · · · · · · · ·  20

      

3-Inch Paper-core Rewinding    · · · · · · · · · · · · ·  21

Basic Usage of the Rewinder  · · · · · · · · · · · · · · ·   ·   23

6-Inch Expansion Option    · · · · · · · · · · · · · · · · · ·  25

Basic Specifications   · · · · · · · · · · · · · · · · · · · · ·  28

Quick Guide

 

Rewinder for SATO Barcode Printer 

R W G 5 0 0

http://www.satoworldwide.com

T h a n k   y o u   f o r   y o u r   p u r c h a s e   o f   t h e   S A T O    

Rewinder RWG500.

Make sure to read this operation manual and 

keep it in a handy place. 

DCS & Labeling Worldwide

Summary of Contents for RWG500

















Reviews: