![background image](http://html1.mh-extra.com/html/savant/smartcontrol-rs232/smartcontrol-rs232_quick-reference-manual_1203494001.webp)
Savant® SmartControl RS232 – Wi-Fi Smart Controller with 2 RS232
Quick Reference Guide
For Product Info
SSC-W02R-00 | 009-1373-03 | 161104
45 Perseverance Way, Hyannis, MA 02601
Copyright © 2016 Savant Systems, LLC
1
of
2
| 508.683.2500
Box Contents
(1) SmartControl RS232 (SSC-W02R-00)
(1) Installation Kit (075-0174-xx)
(1) Mounting Plate (074-0569-xx)
(1) 6-pin Screw Down Plug-in Connector (028-9352-xx)
(1) 5V DC 1.2A Power Supply (025-0165-xx)
(1) Cable Tie (014-0071-xx)
(1) Quick Reference Guide (this document)
Specifications
Environmental
Temperature
32° to 104° F (0° to 40°C)
Humidity
10% to 90% (non-condensing)
Dimensions and Weight (Product)
Height
0.64 in (1.62 cm)
Width
2.70 in (6.85 cm)
Depth
2.67 in (6.78 cm)
Weight
Net: 0.25 lb (0.11 kg)
Shipping: 1.50 lb (0.68 kg)
Power
Input Power
5V DC 1.2A
Max Power
6 watts
Standards
Wireless
Wi-Fi (802.11 b/g/n 2.4 GHz)
Security
WPA™, WPA2™, WPA/WPA2™, WEP
Regulatory
Safety and Emissions
FCC Part 15 | CE Mark | C-Tick
Contains FCC ID:
TLZ-CU277
Contains IC:
6100A-CU277
RoHS
Compliant
Minimum Supported Release
Savant OS
da Vinci 8.2
Network Requirements
Savant requires the use of a wireless network that is configured to
make use of at least one of the supported wireless Standards
listed in the Specifications Table.
Connect all Savant devices to the same local area network (LAN)
or subnet as the host. Savant recommends not implementing any
type of traffic or packet shaping in your network topology for the
Savant devices as this may interfere with performance.
Network Configuration
To ensure that the IP Address will not change due to a power
outage, a static IP Address or DHCP reservation should be
configured. Savant recommends using DHCP reservation within
the router. By using this method, static IP Addresses for all
devices can be managed from a single UI avoiding the need to
access devices individually.
Setting DHCP reservation varies from router to router. Refer to
the documentation for the router to configure DHCP reservation.
Connecting to a Wireless Network
Refer to the
SmartControl RS232 – Wi-Fi Smart Controller with 2
RS232 Deployment Guide
located on the
Savant Customer
Community
to connect the SSC-W02R to the local network.
Front Panel
Press and hold for 5 seconds while powered On to clear network
settings.
Status
LED will blink rapidly when reset is complete.
Off:
No Power
On Solid:
Connected/Communicating with the system Host.
Blinks Once:
In Access Point Provisioning Mode. Ready to be
provisioned to the local network.
Blinks Twice:
Establishing connection with the local network.
Blinks Three Times:
Connected to the local network. Is
connecting to the host.
Short Off Blink:
Firmware is updating.
Rapid Blink:
The reset button was held down for at least five
seconds and the SSC-W02R is performing a factory reset.
Rear Panel
RS-232 Port 1 - 6-Pin Plug-In Connector (Left 3 Pins)
G
Signal Ground
Tx
Transmit Data
Rx
Receive Data
RS-232 Port 2 - 6-Pin Plug-In Connector (Right 3 Pins)
G
Signal Ground
Tx
Transmit Data
Rx
Receive Data
Input Power 5V DC 1.2A Connect to included power supply.
Cable Lance
Use with included cable tie to secure power supply
connection.
A
B
A
B
C
D