background image

P:\INSTALLATION INST\Access Controls\INST-917 QUICK REF\INST-917 QUICK REF.vsd     REV A     05-09    Page 1  

Any suggestions or comments to this instruction or 

product are welcome.  Please contact us through 

our website or email engineer@sdcsecurity.com 

SECURITY DOOR CONTROLS

3580 Willow Lane, Westlake Village, CA 91361-4921  •   (805) 494-0622  •  Fax: (805) 494-8861
www.sdcsecurity.com  •  E-mail: service@sdcsecurity.com

917 QUICK REFERENCE/WORKSHEET

NOTE: [ ] means press keys simultaneously

Factory Default Master Code is 1234 
Make all electrical hookups per drawings in Installation Instructions

Basic Programming:

1.  Enter program mode

2.  Program User code:

3.  Assign User to Main Relay 0:

4.  Set Main Relay time:

5.  Assign REX to Main Relay:

Addtional Programming

6.  Delete User:

7.  Change Master Code:

8.  Reset to factory default settings:

9.  Master Reset

BEWARE!  ERASES MEMORY

BEWARE!  ERASES MEMORY

Press 

[*1]

Master Code

*

Press 

[*1]

Master Code 

[*2]

User Number

PIN Code

PIN Code

*

Press 

[*1]

Master Code 

[*0]

User Number

# 0  *

Press 

[*1]

Master Code 

[*3]

User Number of seconds

# 0 *

Press 

[*1]

Master Code 

[*4]

0 * 

Press 

*

red

 LED will turn on

Touch wire on Pin 10 (GRY/BLK) to wire on Pin 12 (ORG/BLK)

yellow

 LED will turn on.

Release wires.  After 2-3 seconds the 

green

 LED will turn on.

Default Master Code is 1234

User Number from 2-120.  PIN code up to 6 digits

Users can be assigned to Relay 0, & outputs 1-3

Time (1-225 sec.)

REX can be assigned to Relays 0, & outputs 1-3

Press 

[*1]

Master Code 

[*2]

User Number 

# * *

Press 

[*1]

Old Master

[*2]

1

#

New Master

New Master

Press 

[*1]

Master Code 

* Press 

[*9] 

*

Code

Code

Code

Deletes user

Master code is User 1

Erases memory

Erases all memory & returns to factory
default  Master code of 1234.

Note:

If you make an input error before entering *: wait 5 seconds and the command memory will be cleared automatically (or press # to clear manually). Start again.
Five operating errors within 60 seconds will trigger the Auto Lockout function which disables the keypad for 4 minutes and 15 seconds (255 seconds).

Remember the new Master code.

Summary of Contents for 917 EntryCheck








Reviews: