background image

VERG 24V BARRIER

General features

VERG 24V is an electro-mechanical barrier (2, 3, 4, 5 m) 
recommended for the automation of access points which 
require a high opening/closing speed (parking lots, 
motorways, airports, etc.) and frequent use features. The 
automation includes an anti-crush security system with 
adjustable sensitivity, which guarantees a barrier force 
value not exceeding 15 kg, thus protecting people and 
objects from any accidents. A highly reliable slowdown 
device guarantees the total control of the forces of inertia.
The emergency batteries guaranty at least 15 opening 
cycles (depending on the installed accessories) in case of 
power failure and a release system allows the manual 
opening in case of emergency.

English

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

®

The automation system is composed of the following elements:

1   Adjustable mechanical stop
2     Manual release with key
3     Galvanised steel rocker arm.
4     VERG 24V, casing cover with lock and DIN key
5   Balancing spring.
6     Electronic control unit.
7     Foundation plate out of galvanized steel
8     Emergency batteries 2x12V 2Ah.
9   24V       - 2400 rpm  electric motor
10   Reduction gear
11   Cataphoresis-treated and polyester painted   VERG 24V casing, for outside, protects 
all included mechanical and electronic devices from fire, flood, lightning, etc. 
Predisposed for the application of photocells, key switch, proximity reader. Stainless 
steel casing available on request.
12 Battery charger circuit

Main components:

  1) Adjustable mechanical stop
  2) Manual release system
  3) Rocker arm
  4) VERG 24V casing cover
  5) Balancing spring
  6) Electronic control unit
  7) VERG anchoring plate (optional)
  8) Emergency batteries 2x12V 2Ah (optional)
  9) 24V      electric motor
10) Gearbox
11) VERG casing
12) Battery charger circuit (optional with battery kit)

11

6

1

3

4

5

7

8

9

10

11

2

12

Cod. 67411465                                                 Rev.00 - 12/2012                                                              

Summary of Contents for VERG 24V










Reviews:

Related manuals for VERG 24V