TROLLEY JACK 10TONNE LONG REACH
Model no:
10QJ.V4
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAfETY
9
ensure the jack is in sound condition and good working order. Take action for immediate repair or replacement
of damaged parts.
9
Use genuine parts only. The use of unauthorised parts may be dangerous and will invalidate the warranty.
9
locate the jack in a suitable, well lit work area.
9
Keep work area clean and tidy and free from unrelated materials.
9
Use jack on level and solid ground, preferably concrete. Avoid tarmacadam as jack may sink in.
9
Place wedges under wheels of vehicle (but ensure wheels of jack can move freely).
9
ensure the vehicle handbrake is engaged, engine is switched off and transmission is in 1st or reverse gear
(“PARK” if automatic).
9
ensure minimum distance of 0.5m between vehicle and static objects such as doors, walls, etc., to allow for
vehicle tilting.
9
ensure there are no passengers in the vehicle.
9
ensure all non-essential persons keep a safe distance whilst the jack is in use.
9
only place jack under those lifting points recommended by vehicle manufacturer (see vehicle handbook).
9
Check the lifting point is stable and centred on the jack saddle.
9
ensure the jack wheels are free to move and that there are no obstructions.
▲
DANGER:
Use the jack for lifting only,
NOT
for supporting the lifted load.
9
Use suitable capacity axle stands under the vehicle before proceeding with any task.
9
ensure there are no persons or obstructions beneath the vehicle before lowering.
9
Use a qualified person to maintain or repair the jack hydraulic system.
8
DO NOT
operate the jack if damaged.
8
DO NOT
allow untrained persons to operate the jack.
8
DO NOT
exceed the rated capacity of the jack.
8
DO NOT
allow the vehicle to move while supported by the jack, nor use the jack to move the vehicle.
8
DO NOT
jack vehicle if there is a risk of spillage of fuel, battery acid, or other dangerous substance.
8
DO NOT
work under the vehicle until axle stands have been correctly positioned.
8
DO NOT
use the jack for purposes other than that for which it is designed.
8
DO NOT
top up hydraulic system with brake fluid. Use hydraulic jack oil only.
8
DO NOT
adjust the safety overload valve.
9
When not in use store jack, fully lowered, in a safe, dry, childproof area.
2. INTRODuCTION
Heavy-duty chassis with one-piece hydraulic unit. Handle mounted safety release, prevents inadvertent lowering. Fitted with foot operated
quick lift system. Includes large diameter saddle for easier positioning under the jacking point. Fitted with safety overload valve. Fully Ce
approved.
3. SpECIfICATION
Model no: ................................................................. 10QJ.V4
Capacity: ................................................................... 10tonne
length: ..................................................................... 1555mm
Maximum Chassis Height: .......................................... 250mm
Maximum Saddle Height: ........................................... 600mm
Minimum Saddle Height: ............................................ 170mm
4. ASSEMbLY
4.1.
Fit handle by pushing it into the clamp and turning the handle until the key engages with the release valve rod. Tighten the clamp
bolt. Make sure the locking lever is turned to engage in the top of the three holes to keep the handle in the vertical position.
See fig.1.
4.2.
Before initial operation, purge any air from the system by fully opening the pump release valve (turn release valve handle
anticlockwise). Then, while holding the saddle down, pump the handle rapidly several times.
Original Language Version
© Jack Sealey limited
Refer to
instructions
Wear safety
footwear
Apply
Chock
Wheels
Never
exceed
X2
10QJ.V4 Issue 2 (3) 01/08/19
