3.1.
Fit the handle into the handle socket as shown in fig.1
ensuring that it is fully inserted. Retain the handle by
screwing in the handle retaining screw (see fig.1). It may be
necessary to lift the handle slightly in order to get the plain
end of the screw to enter the slot at the bottom of the handle.
3.2.
Before using the jack for the first time, purge the hydraulic
circuit in order to eliminate any air in the system. To do this,
open the release valve by lifting the handle by about 8mm
and turning it through 45° as shown in fig.2A&B. Keeping the
handle in this position pump the foot pedal through its full
travel 6 or 7 times as indicated in fig.2C.
Rotate the handle back to the normal position where it
will drop down to the locked position.
3.3.
Place a few drops of hydraulic jack oil on the pump piston
and pump the handle several times to distribute the oil.
Thoroughly lubricate all moving parts.
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
Important:
Read these instRuctions caRefully. note the safe oPeRational ReQuiReMents, WaRninGs and cautions.
use this Jack coRRectly and With caRe foR the PuRPose foR Which it is intended. failuRe to do so May cause
daMaGe and/oR PeRsonal inJuRy and Will invalidate the WaRRanty. Retain these instRuctions foR futuRe use.
1. safety PRecautions
3. asseMBly & PuRGinG
2. sPecifications
3
Ensure the jack is in sound condition and good working order.
Take action for immediate repair or replacement of damaged
parts. Use genuine parts only. The use of unauthorised parts
may be dangerous and will invalidate the warranty.
3
Locate the jack in a suitable, well lit work area.
3
Keep work area clean and tidy and free from unrelated materials.
3
Use jack on level and solid ground, preferably concrete. Avoid
tarmacadam as jack may sink in.
3
Place chocks under wheels of vehicle (but ensure wheels of
jack can move freely).
3
Ensure the vehicle handbrake is engaged, engine is switched off
and transmission is in 1st or reverse gear (“PARK” if automatic).
3
Ensure minimum distance of 0.5m between vehicle and static
objects such as doors, walls, etc., to allow for vehicle tilting.
3
Ensure there are no passengers in the vehicle.
3
Ensure all non-essential persons keep a safe distance whilst the
jack is in use.
3
Only place jack under those lifting points recommended by
vehicle manufacturer (see vehicle handbook).
3
Check the lifting point is stable and centred on the jack saddle.
3
Ensure the jack wheels are free to move and that there are no
obstructions.
p
danGeR:
Use the jack for lifting only,
not
for supporting the
lifted load.
3
Use suitable capacity axle stands under the vehicle before
proceeding with any task.
3
Ensure there are no persons or obstructions beneath the vehicle
before lowering.
3
Use a qualified person to maintain or repair the jack hydraulic system.
7
do not
operate the jack if damaged.
7
do not
allow untrained persons to operate the jack.
7
do not
exceed the rated capacity of the jack.
7
do not
allow the vehicle to move while supported by the jack,
nor use the jack to move the vehicle.
7
do not
jack vehicle if there is a risk of spillage of fuel, battery
acid, or other dangerous substance.
7
do not
work under the vehicle until suitably rated axle stands
have been correctly positioned.
7
do not
use the jack for purposes other than that for which it is
designed.
7
do not
top up hydraulic system with brake fluid. Use hydraulic
jack oil only.
7
do not
adjust the safety overload valve.
3
When not in use store jack, fully lowered, in a safe, dry,
childproof area.
Original Language Version
fig.2
fig.1
Model: . . . . . . . . . . . . 1510hl . . 2010hl . . 3010hl
capacity:
. . . . . . . . . . . . . . . .1500kg . . . . .2000kg . . . . . 3000kg
Minimum Saddle Height:
. . . .98mm . . . . . .98mm . . . . 130mm
Maximum Saddle Height:
. . .800mm . . . . .735mm . . . . . 860mm
Maximum Chassis Height:
. . .169mm . . . . .210mm . . . . . 210mm
Chassis Length:
. . . . . . . . . .1050mm . . . .1035mm . . . 1620mm
Weight:
. . . . . . . . . . . . . . . . . . . .52kg . . . . . . .53kg . . . . . . . 88kg
InSTRUCTIOnS FOR:
tRolley Jack PReMieR vikinG
- hiGh lift
MODEL no's:
1510hl, 2010hl, 3010hl
1510HL, 2010HL,3010HL Issue: 1 - 17/12/09
Ideal for 4x4 vehicles or vehicles with a high ground clearance. Also
useful for estate cars and vans. Long chassis configuration with up to
two and a half metres of access including the handle. Suitable for
loading bodyshop chassis jigs. Danish design with up to 3 years warranty.
