BENCH MOUNTING BUFFER/POLISHER
150
mm
370W/230V & 200
mm
550W/230V
MODEL NO:
BB1502 & BB2002
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1.
Electrical Safety
WARNING!
It is the user’s responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and all
electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey stockist.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable Appliance
Test) tested.
Electrical Safety Information:
it is important that the following information is read and understood.
1.1.1. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3.
IMPORTANT
: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating in these instructions.
8
DO NOT
pull or carry the appliance by the power cable.
8
DO NOT
pull the plug from the socket by the cable.
8
8
8
DO NOT
use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired
or replaced immediately by a qualified electrician.
1.1.4. This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
A) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
B) Connect the BROWN live wire to the live terminal ‘L’.
C) Connect the BLUE neutral wire to the neutral terminal ‘N’.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2.
GENERAL SAFETY
9
Disconnect the polisher from the mains power before changing accessories, servicing or performing any
maintenance.
9
Replace damaged parts.
Use genuine parts only. Unapproved parts may be dangerous and will invalidate the warranty.
9
Wear approved safety goggles, appropriate dust mask if polisher generates dust and safety gloves.
9
Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery, and contain long hair.
9
Use the polisher in a suitable work area, keep area clean, tidy and free from unrelated materials, and ensure adequate lighting.
9
Maintain correct balance and footing.
DO NOT
over-reach and ensure the floor is not slippery. Wear non slip shoes.
9
Polishing wheels must be securely attached before use, but not over tightened.
9
Keep non essential persons away from the working area, use screens if necessary.
8
DO NOT
operate the polisher if any parts are missing or if the polisher is damaged.
8
DO NOT
use the polisher for a task it was not designed to perform.
8
DO NOT
get the polisher wet or use in damp or wet locations.
8
DO NOT
switch the polisher on whilst the wheel is in contact with the workpiece.
9
Avoid polishing dissimilar metals with the same buffing wheel; galvanic corrosion may occur.
8
DO NOT
touch the workpiece immediately after polishing as it may be very hot.
8
DO NOT
hold unsecured work in your bare hands, and
DO NOT
touch the buffing wheel whilst operating, or whilst plugged into the
mains power.
8
DO NOT
leave the polisher running unattended.
8
DO NOT
operate the polisher when you are tired or under the influence of alcohol, drugs or intoxicating medication.
9
When not in use, switch the polisher off and remove the plug from the power supply.
2. INTRODUCTION
D
esigned for quick and easy smoothing/polishing of metal and other materials. Efficient 550W motor provides sufficient power for most tasks
while the cast iron base reduces vibration. Supplied with fine and coarse buffing/polishing wheels and fitted ASTA approved plug.
B
B1502 & BB2002 | Issue 3 (U) 29/10/18
Original Language Version
© Jack Sealey Limited
Refer to
instructions
Wear eye
protection
Wear protective
gloves
Wear a mask
Recommended fuse
rating:
5A(BB1502)
13A(BB2002)
