background image

10.8V Ø75MM CORDLESS POLISHER - BODY ONLY

MODEL NO: 

CP108VCPBO

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, 

and properly maintained, give you years of trouble free performance.

IMPORTANT:

 PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE 

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR 
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1.  SAFETY

 

9

   Disconnect the polisher from the battery unit before changing accessories, servicing or performing any maintenance.

 

9

   Maintain the polisher and battery in good condition. Check moving parts alignment on a regular basis. 

 

9

   Replace or repair damaged parts. Use an authorised service agent and recommended parts only. Unauthorised parts may be  

 

  dangerous and will invalidate the warranty.

 

9

   Ensure the polisher is switched off before installing the battery pack.

 

9

   Keep the polisher and charger clean for best and safest performance.

 

9

   Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.

 

9

   Evaluate your working area before using the polisher e.g. ceilings, floors and enclosures may contain electrical items or water piping. 

 

9

   Ensure battery pack is correctly inserted into the polisher handle and latched in place before attempting to switch on polisher.

 

9

   Secure loose work pieces with a clamp, vice or other adequate holding device. 

 

9

   Avoid unintentional starting.

 

9

   Wear approved safety eye protection (standard spectacles are not adequate).

 

9

   Maintain correct balance and footing. Ensure the floor is not slippery and wear non-skid shoes.

 

9

   Keep children and unauthorised persons away from the working area.

 

9

   Store polisher and charger in a safe, dry, childproof area where the temperature will not exceed 104°F (40°C).

 

8

  

DO NOT

 use the polisher where there are flammable liquids, solids or gases, such as paint solvents, etc.

 

8

  

DO NOT

 allow children to operate the polisher.

 

8

  

DO NOT

 operate the polisher if any parts are missing as this may cause failure and/or personal injury.

 

8

  

DO NOT

 hold unsecured work piece in your hand.

 

8

  

DO NOT

 leave the polisher operating unattended.

 

8

  

DO NOT

 carry the polisher with your finger on the power switch. 

 

8

  

DO NOT

 use the polisher for a task it is not designed to perform.

 

8

  

DO NOT

 operate the polisher when you are tired or under the influence of alcohol, drugs or intoxicating medication.

 

8

  

DO NOT

 get the polisher or battery wet or use in damp or wet locations. 

2.   INTRODUCTION

C

ompact, lightweight cordless polisher - body only. Comfortable housing with soft grip to help reduce vibration. Variable speed control trigger makes 

this polisher very easy-to-use. Supplied with side handle and polishing pad. Requires compatible 10.8V 2Ah or 4Ah battery and mains charger, sold 

separately.

3.  SPECIFICATION

Model No. .......................................................

CP108VCPBO

B

attery ..................

10.8V 2Ah-4Ah Lithium-ion (not included)

Consumable parts (not included)

 ..........................................................

CP108VBP 2Ah Battery

 ........................................................

CP108VBP4 4Ah Battery

Free speed ..........................................

0-2600rpm/0-7800rpm

Noise power/pressure ..........................................

91/80dB(A)

V

ibration/rating ..............................................

4.7m/s²/1.5m/s²

Pad size ....................................................................

Ø75mm

Replacement parts .....................

CP108VMC - Mains charger

Thread size .......................................................................

M6

4.  OPERATION

4.1.    

Fit battery.

4.2. 

  

BATTERY CHARGE STATUS TEST

4.2.1. 

  

Press trigger, all LEDs lit: battery charged, one LED lit: battery needs 

 charging.

4.3. 

  

In order to maintain battery efficiency:

 

8

  

DO NOT

 fully discharge. After every use fully charge the battery, charge every 4 months even if tool is not used. 

Original Language Version

© Jack Sealey Limited

Refer to 

instruction

manual

Wear protective 

gloves

Wear eye 

protection

Wear face 

mask

Wear ear 

protection

fig.1

C

P108VCPBO   Issue 2 (3)  06/06/22

Reviews: