instructions for
air orbital sander mini disc Ø50mm
model no:
Gsa70
thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. saFetY
1.1.
General saFetY
WarninG!
Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this equipment.
WarninG!
disconnect from air supply before changing accessories or servicing.
9
maintain the sander in good condition (use an authorised service agent).
9
replace or repair damaged parts.
Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
use in a suitable clean and tidy work area and ensure there is adequate lighting.
9
Before each use check abrasive pads for condition. if worn or damaged replace immediately.
9
ensure the abrasive pad rating is the same as, or, greater than the rPm rating of the sander.
9
ensure there are no flammable or combustible materials near the work area.
WarninG!
Always wear approved eye or face and hand protection when operating the sander.
9
use face, dust, or respiratory protection in accordance with cosHH regulations.
9
depending on the task, sander noise level may exceed 85dB, in which case wear safety ear defenders.
9
remove ill fitting clothing. remove ties, watches, rings, other loose jewellery and contain and/or tie back long hair.
9
maintain correct balance and footing. ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and unauthorised persons away from the work area.
9
check moving parts alignment on a regular basis.
9
ensure workpiece is secure before operating the sander. never hold a workpiece by hand.
9
check the workpiece to ensure there are no protruding screws, bolts, nuts, nails, stones, etc.
9
Avoid unintentional starting.
WarninG!
ensure correct air pressure is maintained and not exceeded. recommended pressure 70-90psi.
9
Keep air hose away from heat, oil and sharp edges. check air hose for wear before each use and ensure that all connections are
secure.
9
Prolonged exposure to vibration from this sander poses a health risk. it is the owner’s responsibility to correctly assess the potential
hazard and issue guidelines for safe periods of use and offer suitable protective equipment.
8
do not
use the sander for a task it is not designed to perform.
8
do not
operate sander if any parts are damaged or missing as this may cause failure and/or personal injury.
WarninG! do not
sand any materials containing asbestos.
8
do not
carry the sander by the hose, or yank the hose from the air supply.
8
do not
force, or apply heavy pressure to the sander, let the sander do the work.
8
do not
place air line attachments close to your face and do not point at other persons or animals.
8
do not
operate sander when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
do not
use sander where there are flammable liquids, solids or gases such as paint solvents and including waste wiping or cleaning
rags etc.
8
do not
carry the sander with your finger on the power lever.
8
do not
direct air from the air hose at yourself or others.
9
When not in use disconnect from air supply and store in a safe, dry, childproof location.
1.2.
lead Paint WarninG!
Paint once contained lead as a traditional ingredient. the dust caused by the removal of such paint is toxic and must therefore be
avoided. the following action must be taken before using the sander on a surface that you suspect may contain lead paint.
1. user must determine potential hazard relating to age of paint to be removed (modern paints do not have lead content).
2.
danGer!
Keep all persons and pets away from the working area. the following are particularly vulnerable to the effects of lead paint
dust:
Pregnant women, babies and children.
3. We recommend personal protection by using the following safety items:
a) Paint spray respirator (our ref ssP16en)
b) Pe coated Hooded coverall (our ref ssP267). c) latex Gloves (our ref ssP24).
4. take adequate measures to contain the paint dust, flakes and scrapings.
5.
continue to wear safety equipment as in (3) and thoroughly clean all areas when task is complete.
6. ensure paint waste is disposed of in sealed bags or containers.
GsA70 | issue:3 (l) 21/09/17
Original Language Version
© Jack sealey limited
refer to
instruction
manual
Wear eye
protection
Wear ear
protection
Wear
protective
gloves
Wear
a mask
