background image

I

NSTRUCTIONS FOR:

 

GALVANIZED STEEL SHED GREEN

1.5 x 0.8 x1.5m

MODEL NO:

 

GSS150815G

© Jack Sealey Limited

Original Language Version

 

WARNING! 

Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to  

 

when building this shed.

 

Keep the work area clean, uncluttered and ensure there is adequate lighting.

 

Keep children and unauthorised persons away from the working area.

 

DO NOT

 use the shed for any purpose other than that for which it is designed.

 

Use appropriate safety clothing including eye protection.

  

Note! 

The assembly of this product will require assistance.

  1.  SAFETY INSTRUCTIONS

 2.  INTRODUCTION 

  3.  SPECIFICATION

GSS150815GG    Issue: 1 - 01/09/14

IMPORTANT:

 

PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE 

PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL 

INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these 

instructions, and properly maintained, give you years of trouble free performance.

 

Model No:

  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

GSS15081G

 

Overall Size (W x D x H*):  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1500 x 800 x 1500mm

 

Roof Type:  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Flat

 

*Minimum Wall Height

Galvanized, steel panels easily assembled to form a rigid and secure shed. Has a flat roof and double doors. All other models have skillion (sloping) 

roofs and single doors. Doors are secured by cross bolt and eyelet which will accept a padlock (not included) for additional security. All models are 

supplied with bolt-down fixing kits. 

Summary of Contents for GSS150815G




















Reviews: