background image

INSTRUCTIONS FOR: 

GALVANIZED STEEL 

SHED 1.5 x 0.8 x 1.9m WITH SIDE DOOR.

MODEL NO:

 

GSS150819SDG

WARNING! 

Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when building this shed.

Keep the work area clean, uncluttered and ensure there is adequate lighting.

Keep children and unauthorised persons away from the working area.

DO NOT

 use the shed for any purpose other than that for which it is designed.

Use appropriate safety clothing including eye protection.

Note: 

The assembly of this product will require assistance.

DO NOT 

attempt to assemble in windy weather.

IMPORTANT:

 

PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.  USE THE 

PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL 
INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, 
and properly maintained, give you years of trouble free performance.

1. SAFETY

2. INTRODUCTION

3. SPECIFICATION

Galvanized, steel panels easily assembled to form a rigid and secure shed. Has skillion (sloping) roof and single door. Door are secured by cross 

bolt and eyelet which will accept a padlock (not included) for additional security. Supplied with bolt-down fixing kit. 

Model No:  . . . . . . . . . . . . . . . . . . . . . . . . GSS150819SDG

Overall Size (W x D x H*):

  . . . . . . . .

1500 x 800 x 1900mm

Roof Type:  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Skillion

* Minimum wall height

  GSS150819SDG   Issue: 1 - 27/08/14

 © Jack Sealey Limited

Original Language Version

Summary of Contents for GSS150819SDG



















Reviews: