InstructIons for:
HVLP SPRAY GUNS
thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY
AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
Model no's:
HVLP-750.V3 & HVLP-751.V4
1. SAFETY INSTRUCTIONS
familiarise yourself with the application, limitations and potential hazards peculiar to the spray gun.
WARNING!
disconnect the spray gun from the air supply before changing accessories, servicing or performing any maintenance.
Maintain the
spray gun in good condition (use an authorised service agent).
replace or repair damaged parts.
Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
Keep the spray gun clean for best and safest performance.
ensure that the compressed air system can supply the spray gun air consumption (225l/min - 7.9cfm).
Wear approved safety respiratory protection and safety eye goggles.
If spraying isocynate based finisher, wear approved respirator/clean air breathing apparatus and cover exposed skin with latex gloves and an
impervious hooded coverall.
remove ill-fitting clothing. remove ties, watches, rings and other loose jewellery and tie back long hair.
locate the spray gun in a suitable work area. Keep area clean and tidy and free from unrelated materials and ensure that there is adequate
ventilation and lighting.
Keep children and unauthorised persons away from the work area.
When not in use, ensure that the air supply is turned off.
Avoid unintentional operation of spray gun.
do not point spray gun at yourself, other persons or animals.
do not direct air from the air hose at yourself, other persons or animals.
do not carry the spray gun by the hose, or yank the hose from the air supply.
do not exceed the maximum air pressure of 28psi (1.9 bar).
do not use the spray gun for any purpose other than that for which it is designed.
do not allow untrained persons to operate the spray gun.
do not get the spray gun wet or use in damp or wet locations or in areas where there is condensation.
do not operate the spray gun if any parts are missing or damaged as this may cause failure and/or personal injury.
When not in use, disconnect the spray gun from the air supply, clean thoroughly and store safely.
2. SPECIFICATION
Model HVLP-750.V3 Suction Feed
standard set-up . . . . . . . . . . . . . . . . . . . . . .1.7mm
Available set-ups . . . . . . . . . . . 1.3, 1.4, 1.5, 2mm
Working pressure range. . . . . . 15-28psi (1-1.9bar)
Air consumption . . . . . . . 2.8-7.9cfm (80-225 l/min)
Pot capacity . . . . . . . . . . . . . . . . . . . . . . . . . 900ml
Model HVLP-751.V4 Gravity Feed
standard set-up . . . . . . . . . . . . . . . . . . . . . . 1.3mm
Available set-ups . . . . . . . . . . . 1.4, 1.5, 1.7, 2mm
Working pressure range. . . . . . 15-28psi (1-1.9bar)
Air consumption . . . . . . . 2.8-7.9cfm (80-225 l/min)
Pot capacity . . . . . . . . . . . . . . . . . . . . . . . . . 500ml
Original Language Version
HVlP750.V3, HVlP751.V4 Issue: 2 - 2/11/09
