instructions for
micro air compressor with worklight
12V
model no:
ms163
thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. safety
9
familiarise yourself with the application, limitations and potential hazards of the compressor.
warNiNg!
disconnect the compressor from the battery before changing accessories, servicing or performing any maintenance.
9
this appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
9
use only the supplied adaptors.
9
maintain the compressor in good condition,
Do Not
use if damaged.
9
ensure that there are no flammable or combustible materials (including gases) near the compressor when in use.
WArninG! this compressor is capable of high pressure. do not exceed the maximum safe pressure of the item being inflated.
WArninG! the gauge on the compressor is for guidance only. Where pressure is critical (e.g. tyres) check with a gauge of known
accuracy.
8
Do Not
leave compressor operating unattended.
8
Do Not
operate in wet or damp conditions.
warNiNg!
to prevent overheating and subsequent damage to the unit, switch off after 15 minutes continuous operation and allow to cool
for 15 minutes before switching back on.
9
After use store in a safe, dry, childproof area with the connector locking lever in the unlocked position.
2. iNtroDuctioN
compact design incorporating integrl storage for air output hose. features a work light and pressure guage which reads up to 5.5bar/80psi.
Powered by a 12V motor suitable for inflating tyres on motorcycles and cars. supplied with vehicle accessory socket plug and battery clips.
3. specificatioN
model no .....................................................................ms163
Hose length ............................................................... 100mm
Power cord length ......................................................2.8mtr
operating Voltage ............................................................12V
4. operatioN
4.1. preparation for use:
note: Your ignition may need to be set to position ‘i’ (on) for the 12V output from the 12V accessory socket to function. furthermore, it is
recommended that your car engine is running when using this product so that your battery is not depleted and full power is supplied to the
unit. (Always check that the car is in neutral and the handbrake is on). this compressor is designed for use with a car 12V or motorcycle dc
power supply; do not connect to any other type of electrical power.
4.2. power connection:
connect either the vehical ‘accessory plug or the ‘battery clips’ to the ‘power lead’. for car use, plug in the ‘car accessory plug’ into the cars
accessory socket. for bike use, connect the ‘battery clips’ onto the terminal of the battery. red to + and Black to –.
Note:
When connected the led light will be lit.
4.3. using the compressor:
Attach the air line securely to the valve on the tyre or any other item to be inflated (use adaptors if necessary
screw the adaptors into the Air
Line. Inflating adapters for air rubber rings/air beds/footballs, etc.)
Press the ‘switch’ on and the compressor will start.
The compressor will inflate the tyre (or other item).
Periodically stop the compressor to allow the gauge to steady so that it can be read.
once the correct pressure is reached, switch off and disconnect the air line from the valve.
Note:
it is recommended in the interests of your safety that you check your tyres with a Bs approved tyre gauge to ensure your tyres are at
the correct pressure. Always check your tyres when they are cold.
ms163 | issue 1 30/09/16
Original Language Version
© Jack sealey limited
refer to
instructions
