WARNING!
Ensure Health & Safety, local authority and general workshop practice regulations are adhered to when using this equipment.
WARNING!
Disconnect the hammer from the air supply before changing accessories, servicing or performing any maintenance.
Keep the hammer clean and maintain it in good condition.
Replace or repair damaged parts.
Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty
(use an authorised service agent)
.
Keep the work area clean and uncluttered. Ensure that there is adequate lighting.
Ensure chisels are correctly rated for the job. DO NOT use damaged or suspect chisels.
WARNING!
Wear approved safety eye or face protection, ear defenders and, if dust is generated, respiratory protection.
Keep hands and body clear of the work when operating the hammer.
Maintain correct balance and footing. Ensure that the floor is not slippery and wear non-slip shoes.
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain and/or tie back long hair.
Keep children and unauthorised persons away from the work area.
Secure unstable workpiece with a clamp, vice or other adequate holding device.
Avoid unintentional starting.
WARNING!
Ensure that the correct air pressure is maintained and not exceeded.
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are secure.
DO NOT use the hammer for a task it is not designed to perform.
DO NOT operate the hammer if any parts are damaged or missing as this may cause failure and/or personal injury.
WARNING!
DO NOT chisel into any materials containing asbestos.
DO NOT switch the hammer on whilst the chisel is in contact with
the workpiece.
DO NOT carry the by the hose, or yank the hose from the air supply.
DO NOT hold the workpiece by hand. Use clamps or a vice (not
included) to secure the workpiece. Available from your Sealey dealer.
DO NOT allow untrained persons to operate the hammer.
DO NOT operate the hammer when you are tired or under the
influence of alcohol, drugs or intoxicating medication.
DO NOT use hammer where there is flammable liquid, solid or gas
such as paint solvent, including waste wiping or cleaning rags etc.
DO NOT leave the hammer operating unattended.
DO NOT carry the hammer with your finger on the trigger.
DO NOT direct air from the air hose at yourself or others.
When work is complete ensure that the air supply is turned off.
When not in use disconnect from the air supply and store in a safe,
dry, childproof area.
3. AIR supply
1. sAFETy INsTRuCTIONs
2. INTRODuCTION & spECIFICATION
iNSTRUCTiONS fOR:
lONG sTROkE AIR hAmmER
MODEl No:
GsA11
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT
:
plEAsE READ ThEsE INsTRuCTIONs CAREFully. NOTE ThE sAFE OpERATIONAl REQuIREmENTs, WARNINGs, AND
CAuTIONs. usE ThIs pRODuCT CORRECTly, AND WITh CARE FOR ThE puRpOsE FOR WhICh IT Is INTENDED. FAIluRE TO DO sO
mAy CAusE DAmAGE AND/OR pERsONAl INJuRy AND WIll INVAlIDATE ThE WARRANTy.
Chisel Shank Size: . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.401” Parker Taper
Speed: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3600bpm
Air Consumption: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5cfm
Operating Pressure: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90psi
Air inlet Size: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4”BSP
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3kg
Noise Pressure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92dB.A
Third generation, RWTUV approved air hammer. Handle exhaust reduces noise emission and contoured, soft grip allows added comfort and control. Kit includes
spring retainer, taper punch, long bladed panel cutter, weld buster, panel cutter and cold chisel. Supplied in carry-case.
3.1
Air supply
Recommended hook-up procedure is shown in fig 1.
3.1.1 Ensure tool air valve (or trigger) is in "off" position before connecting to the air supply.
3.1.2 You will require an air pressure of 90psi, and an air flow according to specification.
3.1.3
WARNING!
Ensure the air supply is clean and does not exceed 90psi while operating the tool. Too high an air pressure and unclean air will shorten the
product life due to excessive wear, and may be dangerous causing damage and/or personal injury.
3.1.4 Drain the compressor air tank daily. Water in the air line will damage the tool.
3.1.5 Clean compressor air inlet filter weekly.
3.1.6 line pressure should be increased to compensate for unusually long air hoses (over 8 metres). The minimum hose diameter should be 1/4” i.D. and fittings
must have the same inside dimensions.
3.1.7 Keep hose away from heat, oil and sharp edges. Check hose for wear, and make certain that all connections are secure.
3.2 Couplings.
Vibration may cause failure if a quick change coupling is connected directly to the tool.
To overcome this, connect a leader hose to the tool. A quick change coupling may then be used to connect the leader hose to the air line recoil hose. See
fig 1 & 2 (overleaf).
Risk of hand Arm Vibration Injury
long Stroke G3 Air Hammer Model No. GSA11 when operated in accordance with these instructions and tested in accordance with EN 28662-2: 1994 results in
the following vibration emission declared in accordance with
BS EN12096: 1996.
Measured vibration emission value: . . . . . . . . . . .20m/s² Uncertainty: . . . . . . . 8m/s²
These values are suitable for comparison with emission levels of other tools that have been subject to the same test.
This tool may cause hand-arm vibration syndrome if its use is inadequately managed.
Recommended measures to reduce risk of hand-arm vibration syndrome:
This tool should not be used by an individual regularly for more than 15.3 minutes in any 8 hour period.
This duration of use should be reduced if the individual is exposed to hand-arm vibration from other sources.
Original Language Version
GSA11 issue: 3 - 09/11/10
