3
Follow all workshop Health & Safety rules, regulations and conditions when using tool.
p
p
WARNING!
Disconnect from air supply before changing grinding bit or servicing.
3
Maintain die grinder in good condition and replace any damaged or worn parts.
Use
genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
p
p
WARNING!
Check correct air pressure is maintained and not exceeded. We recommend 90psi.
3
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each
use and ensure that all connections are secure.
p
p
WARNING!
Before each use check grinding bit is secure, and the bit is not worn or damaged.
If damaged, replace immediately.
3
Ensure replacement grinding bits are not damaged (cracks, deformations or splinters etc).
3
Always use a grinding bit suitable for the material being ground. Ensure the maximum speed
specification of the bit is higher than that indicated on the machine data plate.
p
p
WARNING!
Always wear approved eye or face protection when operating the die grinder.
3
Use breathing protection in accordance with COSHH regulations if fumes or dust pose a
hazard.
3
Wear ear defenders and safety gloves.
3
Keep hands and body clear of the workpiece when operating the die grinder.
3
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3
Secure unstable workpiece with a clamp, vice or other adequate holding device.
3
Keep children and non essential persons away from the work area.
3
Avoid subjecting grinding bit to excessive strain, always ease grinding bit against workpiece
(a harsh impact may break the bit). Maintain a controlled progression.
7
DO NOT hold the workpiece by hand. Use clamps or a vice to secure the workpiece.
7
DO NOT use the die grinder for a task it is not designed to perform.
p
p
WARNING!
DO NOT use die grinder if damaged or faulty. Contact your local service agent.
7
DO NOT use die grinder unless you have been instructed in its use by a qualified person.
7
DO NOT carry the die grinder by the air hose, or yank the hose from the air supply.
7
DO NOT direct air from the air hose at yourself or others.
p
p
WARNING!
DO NOT grind any materials containing asbestos.
7
DO NOT turn the die grinder on whilst the grinding bit is in contact with the workpiece.
7
DO NOT use die grinder where there are flammable liquids, solids or gases such as paint
solvents, including waste wiping or cleaning rags etc. as generated sparks may be dangerous.
7
DO NOT touch the workpiece close to the ground surface as it will be very hot. Allow to cool.
The workpiece may also be very sharp.
7
DO NOT operate die grinder if you are tired or under the influence of alcohol,
drugs or intoxicating medication.
3
When not in use disconnect from air supply and store in a safe, dry, childproof location.
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
INSTRUCTIONS FOR:
MICRO AIR DIE GRINDER
MODEL NO:
SA673
PARTS LIST FOR:
MICRO AIR DIE GRINDER
MODEL NO:
SA673
Declaration of Conformity
For Jack Sealey Ltd. Sole importer into the UK
of Sealey Power Tools.
Micro Air Die Grinder Models: SA673
98/37/EC Machinery Directive
93/68/EEC CE Marking Directive
30th May 2005
Signed by Mark Sweetman
We, the sole importer into the UK, declare that the product listed here is in conformity with the
following standards and directives. The construction file for this product is held by the
Manufacturer and may be inspected, by a national authority, upon request to Jack Sealey Ltd.
Issue No. . . . . . . . . .1
Issue Date . . . .300505
01284 757500
E-mail: sales@sealey.co.uk
Web: www.sealey.co.uk
01284 703534
Sole UK Distributor, Sealey Group
, Bury St. Edmunds, Suffolk.
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component
parts without prior notice.
IMPORTANT:
No liability is accepted for incorrect use of this equipment.
WARRANTY:
Guarantee is 12
months from purchase date, proof of which will be required for any claim.
INFORMATION:
For a copy of our latest catalogue and
promotions call us on 01284 757525 and leave your full name and address, including postcode.
1.
SAFETY INSTRUCTIONS
SA673 - 1 - 300505
ITEM PART NO. DESCRIPTION
01.
SA673.01 CLAMPING NUT
02.
SA673.02 COLLET
03.
SA673.03 FRONT COVER
04.
SA673.04 COLLET BASE
05.
SA673.05 BALL BEARING
06.
SA673.06 SPACER
07.
SA673.07 LATERAL DISC
08.
SA673.08 CYLINDER
09.
SA673.09 ROTOR
10.
SA673.10 ROTOR BLADE
11.
SA673.11 PIN
12.
SA673.12 BEARING PLATE
ITEM PART NO. DESCRIPTION
13.
SA673.13 BALL BEARING
14.
SA673.14 INTAKE PLATE
15.
SA673.15 SLEEVE
16.
SA673.16 INTAKE TUBE
17.
SA673.17 HOSE PLUG
18.
SA673.18 PIN
19.
SA673.19 SLIDING RING
20.
SA673.20 O-RING
21.
SA673.21 O-RING
22.
SA673.22 SCREW
23.
SA673.23 REAR END HOLDER
