background image

3

Ensure that the jack is in good working order. Take action for immediate repair or replacement of damaged parts. 

Use genuine parts only. The use of unauthorised parts may be dangerous and will invalidate the warranty.

3

Locate the jack in a suitable, well lit work area.

3

Keep work area clean and tidy and free from unrelated materials.

3

Use jack on level and solid ground, preferably concrete. 

Avoid tarmacadam as jack may sink in

.

3

Place wedges under wheels of vehicle (

but ensure wheels of jack can move freely).

3

Ensure the vehicle handbrake is engaged, engine/motor is switched off and transmission is in 1st or reverse gear.

3

Ensure minimum distance of 0.5m between vehicle and static objects such as doors, walls, etc., to allow for vehicle tilting.

3

Only place jack under those lifting points recommended by the vehicle manufacturer 

(see vehicle handbook).

3

Ensure there are no passengers in the vehicle.

3

Ensure all non-essential persons keep a safe distance whilst the jack is in use.

3

Check the lifting point is stable and centred on the jack saddle.

3

Ensure the jack wheels are free to move and that there are no obstructions.

p

DANGER: 

Use the jack for lifting only, 

NOT

for supporting the lifted load.

3

Use suitable capacity axle stands under the vehicle before proceeding with any task.

3

Ensure there are no persons or obstructions beneath the vehicle before lowering.

3

Use a qualified person to maintain or repair the jack hydraulic system.

7

DO NOT

operate the jack if damaged.

7

DO NOT

allow untrained persons to operate the jack.

7

DO NOT

exceed the rated capacity of the jack.

7

DO NOT

work under the vehicle until axle stands have been correctly positioned.

7

DO NOT

use the jack for purposes other than that for which it is designed.

7

DO NOT

top up hydraulic system with brake fluid. Use hydraulic jack oil only.

7

DO NOT

adjust the safety overload valve.

7

DO NOT

jack vehicle if there is a risk of spillage of fuel, battery acid, or other dangerous substance.

7

DO NOT

allow the vehicle to move while supported by the jack and 

DO NOT

use the jack to move the vehicle.

3

When not in use store jack, fully lowered, in a safe, dry, childproof area.

p

p

 

 

 

 

WARNING!

It is 

very dangerous

to go under a vehicle which is supported by a jack 

even

if additional supports are used. 

DO NOT

go under a

vehicle unless it is supported by adequately rated axle stands.

s

s

 

 

 

 

IMPORTANT! Ensure that you can see the saddle and jacking point throughout the jacking operation in case there is

any relative movement.

2.1. Line up the holes in the two piece handle and fasten with the assembly screw. 

2.2. Loosen location bolt at the side of the handle base. Insert Jack handle and tighten the bolt.

INSTRUCTIONS FOR: 

TROLLEY JACK

Your new Trolley Jack is produced and manufactured to a high standard of dependability and will, if used according to these instructions and

properly maintained, give you years of trouble free performance.

IMPORTANT:

READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE

THIS JACK CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR

PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. RETAIN THESE INSTRUCTIONS FOR FUTURE USE.

1. SAFETY PRECAUTIONS

2. ASSEMBLY

3.1. Before first use.

3.1.1. Before using the Jack, purge hydraulic circuit in order to eliminate any air in the system

by turning the handle anti-clockwise to open, and pumping 8 or 9 times (fig.1).

3.1.2. Place a few drops of hydraulic jack oil on the pump piston and pump the handle a several times 

to distribute the oil. Thoroughly lubricate all moving parts.

3.2. General jacking.

p

p

WARNING! Before lifting ensure Section 1 safety instructions are strictly followed. 

3.2.1. Prepare the vehicle as mentioned in the safety instructions ensuring the ground on which 

the Jack is to stand is level and solid (not tarmacadam).

3.2.2. Position the Jack saddle under the vehicle manufacturer’s recommended lifting point. 

3.3. Jacking the vehicle.

3.3.1. Turn the handle clockwise to close the valve and commence pumping the handle up and down using maximum strokes until the vehicle

reaches the working height. 

3.3.2. Should the Jack become overloaded, a safety excess pressure valve will open, and stop the vehicle from lifting.

3.4. Lowering the vehicle 

Turn the handle anti-clockwise, very slowly, to open the valve.

The lowering speed is controlled by the amount you turn the handle. Lower carefully, avoid any sudden release. 

p

SAFETY WARNING!

Always lower in a slow and controlled manner and 

ensure there are no persons or obstacles beneath the vehicle, 

or in the path of its descent.

3. OPERATING INSTRUCTIONS

fig. 1

Model 2080CX Specifications

Capacity  . . . . . . . . . . . . . . .2.25 tons

Min. Saddle height  . . . . . . . . .118mm

Max. Saddle height  . . . . . . . . .475mm

Hydraulic lift  . . . . . . . . . . . . . .357mm

Length/Width/Height . 640/350/160mm

Weight  . . . . . . . . . . . . . . . . . . . .33kg

Models:   2080CX  &  3080CX

Model 3080CX Specifications

Capacity  . . . . . . . . . . . . . . . . . .3 tons

Min. Saddle height  . . . . . . . . .120mm

Max. Saddle height  . . . . . . . . .485mm

Hydraulic lift  . . . . . . . . . . . . . .365mm

Length/Width/Height  .675/360/160mm

Weight  . . . . . . . . . . . . . . . . . . . .38kg

2080CX, 3080CX - 3 - 011003

Reviews: