Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.
SAFETY INSTRUCTIONS
7.
PARTS LIST
p
WARNING!
Ensure Health & Safety, local authority and general workshop practice regulations are adhered to
when using this equipment.
p
WARNING!
Disconnect from air supply before changing accessories or servicing.
3
Maintain the sander in good condition (use an authorised service agent).
3
Replace or repair damaged parts.
Use genuine parts only. Unauthorised parts may be dangerous and
will invalidate the warranty.
3
Use in suitable, clean and tidy work area, free from unrelated materials. Ensure that there is adequate lighting.
3
Before each use check abrasive for condition. If worn or damaged replace immediately.
3
Ensure the correct abrasive pad size is used.
3
Ensure there are no flammable or combustible materials near the work area.
p
WARNING!
Always wear approved eye or face and hand protection when operating the sander.
3
Use face, dust, or respiratory protection in accordance with COSHH regulations.
3
Depending on the task, sander noise level may exceed 85dB, in which case wear safety ear defenders.
3
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain and/or tie
back long hair.
3
Wear appropriate protective clothing and keep hands and body clear of working parts.
3
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3
Keep children and unauthorised persons away from the work area.
3
Check moving parts alignment on a regular basis.
3
Ensure that workpiece is secure before operating the sander. Never hold a workpiece by hand.
3
Check the workpiece to ensure that there are no protruding screws, bolts, nuts, nails, stones, etc.
3
Avoid unintentional starting.
p
WARNING!
Ensure correct air pressure is maintained and not exceeded. Recommended pressure 70-90psi.
3
Keep air hoses away from heat, oil and sharp edges. Check air hose for wear before each use and ensure
that all connections are secure.
3
Prolonged exposure to vibration from this sander poses a health risk. It is the owners responsibility to correctly
assess the potential hazard and issue guidelines for safe periods of use and offer suitable protective equipment.
7
DO NOT use the sander for a task it is not designed to perform.
7
DO NOT operate sander if any parts are damaged or missing as this may cause failure and/or personal injury.
p
WARNING!
DO NOT sand any materials containing asbestos.
7
DO NOT carry the sander by the hose, or yank the hose from the air supply.
7
DO NOT force, or apply heavy pressure to, the sander. Let the sander do the work.
7
DO NOT place attachments close to your face and do not point at other persons or animals.
7
DO NOT operate sander when you are tired or under the influence of alcohol, drugs or intoxicating medication.
7
DO NOT use sander where there are flammable liquids, solids or gases such as paint solvents and including
waste wiping or cleaning rags etc.
7
DO NOT carry the sander with your hand on the power lever.
7
DO NOT direct air from the air hose at yourself or others.
3
When not in use disconnect from air supply and store in a safe, dry, childproof location.
SA32 - 1 - 250202
INSTRUCTIONS FOR
AIR OPERATED TWIN PISTON
IN-LINE SANDER
Model:
SA32
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component
parts without prior notice.
IMPORTANT:
No liability is accepted for incorrect use of this equipment.
WARRANTY:
Guarantee is 12
months from purchase date, proof of which will be required for any claim.
INFORMATION:
For a copy of our latest catalogue and
promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
E-mail:
sales@sealey.co.uk
01284 703534
Sole UK Distributor, Sealey Group
, Bury St. Edmunds, Suffolk.
Item
Part No.
Description
1
SA32/01
Socket Head Screw
2
SA32/02
Front Cap
3
SA32/03
Piston
4
SA32/04
Plug
5
SA32/05
Piston Ring
6
SA32/06
Front Gasket
7
SA32/07
Body
8
SA32/08
Knob
9
SA32/09
Wear Plate
10
SA32/10
Socket Head Screw
11
SA32/11
Bushing
12
SA32/12
Gear
13
SA32/13
Gear Shaft
14
SA32/14
Plunger
15
SA32/15
O-ring
16
SA32/16
Adjuster Shaft
17
SA32/17
Actuator Valve
18
SA32/18
Actuator Gear
19
SA32/19
Washer
20
SA32/20
Flat Head Screw
Item
Part No.
Description
21
SA32/21
Handle
22
SA32/22
Phillips Head Screw
23
SA32/23
Trigger
24
SA32/24
Roll Pin
25
SA32/25
Phillips Head Screw
26
SA32/26
Hex. Nut
27
SA32/27
Washer
28
SA32/28
Carrier
29
SA32/29
Pad Assembly
30
SA32/30
Side Strap
31
SA32/31
Phillips Head Screw
32
SA32/32
Rear Gasket
33
SA32/33
Rear Cap
34
SA32/34
Bushing
36
SA32/36
Valve Pin
37
SA32/37
O-ring
38
SA32/38
Valve Spring
39
SA32/39
Valve Plug
40
SA32/40
Socket Head Screw
41
SA32/41
Hose Adaptor
Issue No:
1
Date Issued: 250202
