Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE OR PERSONAL INJURY AND WILL INVALIDATE THE
WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.
SAFETY INSTRUCTIONS
p
WARNING!
Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to
when using this equipment.
p
WARNING!
Disconnect from air supply before changing accessories or servicing.
3
Maintain the sander in good condition (use an authorised service agent).
3
Replace or repair damaged parts.
Use genuine parts only. Non-authorised parts may be dangerous and
will invalidate the warranty.
3
Use in suitable clean and tidy working area, free from unrelated materials and ensure there is adequate lighting.
3
Before each use check abrasive pads for condition. If worn or damaged replace immediately.
3
Ensure the abrasive pad rating is the same as, or, greater than the RPM rating of the sander.
3
Ensure there are no flammable or combustible materials near the work area.
p
WARNING!
Always wear approved eye or face and hand protection when operating the sander.
3
Use face, dust, or respiratory protection in accordance with COSHH regulations.
3
Depending on the task, sander noise level may exceed 85dB in which case wear safety ear defenders.
3
Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery, and contain and/or tie back long hair.
3
Wear appropriate protective clothing and keep hands and body clear of working parts.
3
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3
Keep children and unauthorised persons away from the working area.
3
Check moving parts alignment on a regular basis.
3
Ensure workpiece is secure before operating the sander. Never hold a workpiece by hand.
3
Check the workpiece to ensure there are no protruding screws, bolts, nuts, nails, stones, etc.
3
Avoid unintentional starting.
p
WARNING!
Ensure correct air pressure is maintained and not exceeded. Recommended pressure 70-90psi
3
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure
that all connections are secure.
3
Prolonged exposure to vibration from this sander poses a health risk. It is the operators responsibility to correctly
assess the potential hazard and issue guidelines for safe periods of use and offer suitable protective equipment.
7
DO NOT use the sander for a task it is not designed to perform.
7
DO NOT operate sander if any parts are damaged or missing as this may cause failure and/or personal injury.
7
DO NOT use cloth backed sanding pads. Use only appropriate paper adhesive pads, following pad instructions.
p
WARNING!
DO NOT sand any materials containing asbestos.
7
DO NOT carry the sander by the hose, or yank the hose from the air supply.
7
DO NOT force, or apply heavy pressure to the sander, let the sander do the work.
7
DO NOT place attachments close to your face and do not point at other persons or animals.
7
DO NOT operate sander when you are tired, under the influence of alcohol, drugs or intoxicating medication.
7
DO NOT use sander where there is flammable liquids, solids or gases such as paint solvents and including
waste wiping or cleaning rags etc.
7
DO NOT carry the sander with your finger on the power lever.
7
DO NOT direct air from the air hose at yourself or others.
3
When not in use disconnect from air supply and store in a safe, dry, childproof location.
SA7/S - 0016 - (1) - 220800
INSTRUCTIONS FOR
AIR OPERATED RANDOM
ORBITAL SANDER
Model:
SA7/S
01284 757500
E-mail:
sales@sealey.co.uk
01284 703534
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component
parts without prior notice.
IMPORTANT:
No liability is accepted for incorrect use of this equipment.
WARRANTY:
Guarantee is 12
months from purchase date. proof of which will be required for any claim.
INFORMATION:
Call us for a copy of our latest catalogue
and promotions on 01284 757525 and leave your full name and address including your postcode.
Sole UK Distributor, Sealey Group
, Bury St. Edmunds, Suffolk.
1
SA7S/01
SCREW
2
SA7S/02
FLAT WASHER
3
SA7S/03
WASHER WAVE
4
SA7S/04
SPINDLE LOCK
5
SA7S/05
SPACER
6
SA7S/06
WAVE WASHER
7
SA7S/07
HEX. NUT
9
SA7S/09
RETAINING RING
10
SA7S/10
WAVE WASHER
11
SA7S/11
DRIVE SPINDLE
12
SA7S/12
USE B/6201ZZ BEARING
13
SA7S/13
WASHER WAVE
14
SA7S/14
FONT SCREW
15
SA7S/15
ORBITAL HUB
16
SA7S/16
SOCKET SCREW
17
SA7S/17
ROTOR SHAFT
18
SA7S/18
KEY
19
SA7S/19
WAVE WASHER
20
SA7S/20
USE B/6200Z BEARING
21
SA7S/21
END PLATE
22
SA7S/22
ROTOR
23
SA7S/23
ROTOR BLADE [9mm]
24
SA7S/24
CYLINDER
25
SA7S/25
LOCATING PIN
26
SA7S/26
O-RING
27
SA7S/27
RETAINING RING
28
SA7S/28
CAP SCREW (S)
29
SA7S/29
CAP SCREW (L)
30
SA7S/30
RIVE HOUSING
31
SA7S/31
GASKET
32
SA7S/32
MOTOR HOUSING
33
SA7S/33
HOUSING COVER
34
SA7S/34
VALVE-SPEED REGULATOR
35
SA7S/35
O-RING
36
SA7S/36
RING RETAINING
37
SA7S/37
THROTTLE VALVE SPRING
38
SA7S/38
O-RING
39
SA7S/39
VALVE STEM
40
SA7S/40
O-RING
41
SA7S/41
O-RING
42
SA7S/42
VALVE BODY
43
SA7S/43
BRACKET
44
SA7S/44
HINGE SCREW
45
SA7S/45
HEX. NUT
46
SA7S/46
LOCK WASHER
47
SA7S/47
HEX. NUT
48
SA7S/48
THROTTLE LEVER
49
SA7S/49
HANDING COVER
50
SA7S/50
HOSE ADAPTOR
SA7S/RG RANDOM BALANCE GUARD
Item Part No
Description
Item Part No
Description
Original Date:
220800
Issue Date:
220800
Issue No:
1
Date Modified:
N/A
