background image

Model No.  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SSB37W 

Capacity (Weight)  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 37kg 
Capacity (Volume)   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 29ltr 
Spread   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 3-3 .6mtr 
Weight   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 10 .44kg 
Dimensions (W x D x H) .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .550 x 940 x 860mm 

Manufactured with a strong tubular stainless steel frame and polypropylene dispensing hopper . Features corrosion resistant stainless steel 
feed system ideal for spreading salt and grit . Fitted with nylon gear and adjustable feed system . Sprays in 360° motion to cover a large area . 
Suitable for a variety of horticultural agents including grit, seed, salt, fertiliser and weed killer . 

Original Language Version

SSB37W    Issue: 3 (SP)  - 11/09/15

ü

  Before each use, check that there is no damage to the spreader and that all fixings are tight .

ü

  Replace or repair damaged parts . 

Use only recommended parts.Unauthorised parts may be dangerous and will invalidate the warranty.

 

ü

  Ensure that the operator is fully trained and competent to operate the spreader .

ü

  Ensure that all chemical safety instructions are adhered to when handling products for use in the spreader . A full range of personal   

 

safety equipment is available from your Sealey dealer .

ü

  Ensure all non essential personnel keep a safe distance when the spreader is in use .

 

DO NOT 

place hands inside the hopper during spreading .

 

DO NOT 

over inflate the tyres, 25psi (1 .7bar) maximum .

 

DO NOT

 overload the spreader - see Specification .

 

DO NOT

 leave unattended, especially when loaded .

 

DO NOT

 allow anybody to sit, stand, or ride on the spreader .

 

DO NOT

 allow untrained personnel to use the spreader .

 

DO NOT

 allow children to play in or climb onto the spreader .

 

DO NOT

 use on windy days when spreading seeds or herbicides .

 

DO NOT

 tow this spreader with a motorized vehicle of any sort .

 

DO NOT

 use the spreader for purposes other than for which it is designed .

 

DO NOT 

operate the spreader when you

 

are tired or under the influence of alcohol, drugs or intoxicating medicines .

   

DO NOT 

operate the spreader over edges, rough surfaces etc ., where the spreader is at risk of overturning .

 

 

WARNING! 

Failure to comply with these instructions may result in damage to spreader or other property and/or personal injury . 

  WARNING! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that   

 

may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into   

 

this product, but must be applied by the operator.

NOTE: 

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or   

 

lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a   

 

person responsible for their safety . Children should be supervised to ensure that they do not play with the appliance .

InSTRuCTIonS FoR: 

STAINLESS STEEL BROADCAST SALT 
SPREADER 37kG WALk BEhIND

MoDEl no:

 SSB37W

 1. SAfETy

 2. INTRODuCTION

 3. SPECIfICATION

 © Jack Sealey limited

IMPORTANT:

 

PLEASE READ ThESE INSTRuCTIONS CAREfuLLy. NOTE ThE SAfE OPERATIONAL REQuIREMENTS, WARNINGS & CAuTIONS.  uSE ThE PRODuCT 

CORRECTLy AND WITh CARE fOR ThE PuRPOSE fOR WhICh IT IS INTENDED. fAILuRE TO DO SO MAy CAuSE DAMAGE AND/OR PERSONAL INJuRy AND WILL 
INVALIDATE ThE WARRANTy. kEEP ThESE INSTRuCTIONS SAfE fOR fuTuRE uSE.

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these 
instructions, and properly maintained, give you years of trouble free performance.

Refer to

instruction 

manual

Summary of Contents for SSB37W









Reviews: