background image

1

PARTS  CATALOGUE 

/

 TECHNICAL GUIDE

Cal. S140A, S143A

Cal. No.

Item

S140A

(x 0.7)

The illustrations refer to Cal. S143A.

Module

Module size

Outside diameter

49.3 mm between 6 o’clock and 12 o’clock sides
43.0 mm between 3 o’clock and 9 o’clock sides

[SPECIFICATIONS]

S143A

Casing diameter

Height

8.75 mm

Display medium

Nematic Liquid Crystal, FEM (Field Effect Mode)

Liquid crystal driving system

1/4 multiplex driving system

Display system

• Stopwatch display (Up to 10 hours)

Split time/lap time measurement

Total time measurement/lap time measurement in progress

• Time/calendar display

• Stroke display (Only for Cal. S140A)

Additional mechanism

• Memory function: Up to 300 measurements

• Memory capacity indicator

• Confirmation sound for watch operation

• Contrast adjustment function

• Battery life indicator

• Printout function (Only for Cal. S143A)

Regulation system

Nil

Measuring gate by quartz tester

Any gate can be used.

Battery

SEIKO CR2430, Sony CR2430
Battery life is approximately 3 years.
(When the stopwatch is used for 3 hours a day or less)
Voltage:  3.0 V

±

0.0006% at normal temperature range (corresponds to a loss/gain

(monthly rate) of less than 15 seconds)

Loss/gain

Summary of Contents for S140A













Reviews: