background image

AIG-10043-03

Smart Gateway

Installation Guide

Getting Started

 

Sensus Provided Components

•  Sensus Smart Gateway unit

•  Wall Mount Kit: 1 cable gland with single 

hole insert (5-10 mm wire), 4 Phillips 

head screws, 4 mounting feet 

OR

•  Pipe/Wall Mount Kit: 1 cable 

gland with single hole insert 

(5-10mm wire), 4 Phillips head 

screws, 2 mounting bars, 4 

mounting feet

Sensus Optional Components

•  Multi-Cable Kit: 1 cable 

gland with 2 two hole 

inserts (4.5-6mm wire 

each) and 1 single hole 

insert

Customer Provided 

Components

•  Transducer with Cable (1)

•  Hose clamp (2), ≤.5 in. width - used in 

pipe mount

•  Appropriate mounting screws - used in 

wall mount

Prerequisite(s)

Read all sensor documentation first to 

ensure you are familiar with your particular 

sensor wiring. 

1.  Using a screwdriver and a hammer, 

punch out a hole for the cable 

through one of the knock-outs on 

the bottom of the enclosure as 

shown (Figs. 1&2).

Caution: Take care not to hit or damage the 

internal battery.

2.  Take the cable gland out of the 

provided kit. Install the cable gland 

through the hole you just punched 

out (Fig. 3) in such a way that the 

gasket is on the outside of the 

enclosure. Tighten the nut on the 

inside but not the cable gland (Fig. 

4).

Note: 

The provided cable gland can 

accommodate one (1) 5-10 mm wire. To 

accommodate additional wires please order 

the optional multi-wire kit from Sensus.

3.  Run your customer provided 

transducer cable through the cable 

gland and into the center of the 

Smart Gateway module (Fig. 5) to 

measure the length. Pull back out to 

butt the cable sheath approximately 

8 inches and strip the wires 

approximately .25 inch. Trim any 

unnecessary wires.

4.  Run the stripped cable through the 

cable gland and then tighten the 

cable gland to hold the cable in 

place. You will want to make sure 

that the wire has enough give in it 

so the lid will close without bending 

or breaking the wire.

5.  Using the #0 Phillips screwdriver, 

loosen the screws in the terminal 

block.

Installation

Fig. 1: Punch cable hole

Fig. 2: Cable hole punched out

Fig. 3: Attach cable gland

Fig. 5: Run cable through to measure

Fig. 4: Tighten nut on inside

Tools (customer provided)

•  Hammer & Wrench

•  #2 and #0 Phillips screwdriver

•  Wire trimmers 

• 

Large flathead screwdriver (depending 

on customer’s pipe mount)

Summary of Contents for AIG-10043-03

Page 1: ...and through the hole you just punched out Fig 3 in such a way that the gasket is on the outside of the enclosure Tighten the nut on the inside but not the cable gland Fig 4 Note The provided cable gland can accommodate one 1 5 10 mm wire To accommodate additional wires please order the optional multi wire kit from Sensus 3 Run your customer provided transducer cable through the cable gland and int...

Page 2: ...t around the cable and the nut that secures the cable gland to the housing is tightened firmly Close the lid of the module Fig 8 Fig 8 Closed module with cable installed AIG 10043 03 Smart Gateway Installation Guide Fig 7 Pin layout label Fig 6 Attach sensors Sensor Connection If you are using a 2 wire sensor Connect the sensor power to the terminal labeled Sensor Connect the sensor 4 20 mA output...

Page 3: ...mer provided clamps through the Sensus provided mounting bars Fig 10 2 Using a 2 Phillips screwdriver attach one of the provided mounting bars with clamp installed to the back of the unit using the provided screws 3 Repeat for the second mounting bar and band hose clamp 4 Attach the unit to the pipe using the band hose clamps You can mount the unit to a horizontal or vertical pipe Fig 11 shows the...

Page 4: ...ion Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may c...

Reviews: