background image

KB-3401LS

KB-3401LK

KB-3401LW

This is a supplemental Service Manual and is quite similar to the base models KB-3300JS/JK/JW; (S74R243KB330J). This 
supplemental manual must be used in conjunction with the base model service manual for complete operation, service, safety 
and replacement parts information.

WARNING TO SERVICE PERSONNEL: 

This service manual is intended for use by persons having electrical and mechanical training and a level of 
knowledge of these subjects generally considered acceptable in the appliance repair trade. Sharp Electronics 
Corporation  cannot be responsible, nor assume any liability, for injury or damage of any kind arising from the 
use of this manual. 

Microwave ovens contain circuitry capable of producing very high voltage and current. Contact with the 
following parts may result in a severe, possibly fatal, electrical shock. (High Voltage Capacitor, High Voltage 
Power Transformer, High Voltage Rectifier and Heat sink etc., and Magnetron,  High Voltage Harness etc..)

S76R266KB3401F

KB-3401LS

KB-3401LK

KB-3401LW

 

FREE STANDING RANGE 

WITH MICROWAVE DRAWER

MODELS

 

SUPPLEMENTAL SERVICE MANUAL

TABLE OF CONTENTS

 

Page

PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO
AVOID POSSIBLE  EXPOSURE TO EXCESSIVE MICROWAVE ENERGY ..................... INSIDE FRONT COVER
BEFORE SERVICING ....................................................................................................... INSIDE FRONT COVER
WARNING TO SERVICE PERSONNEL ................................................................................................................. 3
MICROWAVE MEASUREMENT PROCEDURE ..................................................................................................... 5
FOREWORD AND WARNING ............................................................................................................................... 7
PRODUCT SPECIFICATIONS ............................................................................................................................... 8
POWER CONNECTION ....................................................................................................................................... 0
ANTI-TIP DEVICE ................................................................................................................................................ 2
CONTROL LAYOUT ............................................................................................................................................. 3
SCHEMATICS ...................................................................................................................................................... 4
TOUCH CONTROL PANEL ASSEMBLY .............................................................................................................. 8
OVEN/MICROWAVE DRAWER DISASSEMBLY .................................................................................................. 23
WIRING DIAGRAMS ............................................................................................................................................ 33
PRINTED WIRING BOARDS ............................................................................................................................... 39
PARTS LIST ......................................................................................................................................................... 44
PACKING AND ACCESSORIES .......................................................................................................................... 56

This document has been published to be used for after sales service only. The contents are subject to change without notice.

SHARP ELECTRONICS CORPORATION

KB-340LW pictured

Summary of Contents for KB3401LK - 30 Inch Electric Range





























































Reviews: