background image

1

SPECIAL WARNING

INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.
IMPORTANT: SAVE this installation manual FOR LOCAL ELECTRICAL INSPECTOR’S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

CLEARANCES AND DIMENSIONS

For SAFETY CONSIDERATIONS do not install drawer in any combustible cabinetry, which is not in accord with the stated 

clearances and dimensions on pages 2 - 5. See Figures 1 - 7.

Microwave Drawer : SMD2480CS

INSTALLATION MANUAL

UNPACKING YOUR MICROWAVE DRAWER

•  

Remove all packing 

materials from inside 

the Microwave Drawer. 

DO NOT REMOVE 

THE WAVEGUIDE 

COV ER, which is 

located on the top of 

the Microwave Drawer. 

•  

Remove the feature 

sticker, if there is one. 

Check the drawer for 

any damage, such as 

misaligned or bent 

drawer, damaged drawer 

seals and sealing surfaces, broken or loose Microwave Drawer 

guides and dents inside the cavity or on the front side of the 

drawer. If there is any damage, do not operate the Microwave 

Drawer and contact your dealer or a SHARP AUTHORIZED 

SERVICER.

IMPORTANT NOTES TO THE INSTALLER

 •  

Read all of the Installation Manual before installing the 

Microwave Drawer.

  •  

Remove all packing material before connecting the electrical 

supply.

  •  

Observe all governing codes and ordinances.

  •  

Be sure to leave these instructions with the consumer.

IMPORTANT NOTES TO THE CONSUMER

Keep this manual with your Operation Manual for future 

reference.
 

•  

As when using any microwave oven generating heat, there 

are certain safety precautions you should follow. These are 

listed in the Operation Manual. Read all and follow carefully.

 

•  

Be sure your Microwave Drawer is installed and grounded 

properly by a qualified installer or service technician.

IMPORTANT SAFETY INSTRUCTIONS

 If the information in this manual is not followed 

exactly, a fire or electrical shock may result that could cause 

property damage, personal injury or death.

 To reduce the risk of tipping, the Microwave 

Drawer must be secured by a properly installed Anti-Tip block.
 

•  

This Microwave Drawer must be electrically grounded in 

accordance with local codes.

 

•  

Make sure the wall coverings and the cabinets around the 

Microwave Drawer can withstand the heat generated by the 

Microwave Drawer.

 Never leave children alone or unattended in 

the area where a Microwave Drawer is in use. Never leave the 

drawer open when the microwave is unattended.

 Stepping, leaning or sitting on the drawer may 

result in serious injuries and can also cause damage to the 

Microwave Drawer.
 

•  

Do not use the Microwave Drawer as a storage space. 

This creates a potentially hazardous situation.

 

•  

Check that the time-of-day is in the display. If not, 

touch STOP/CLEAR 

for safety reasons and 

to prevent 

unintended use.

1

Waveguide 

Cover

Sealing 

Surface

Oven 

Cavity

Sealing 

Surface

Summary of Contents for SMD2480CS









Reviews: