background image

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OWNER’S AND OPERATOR’S MANUAL 

 

 

 

 

 

 

Vertical, Water-Cooled 4-Cycle Diesel Engine 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DGK15FL 

X753-008 31 0 

X753801-470 0 

 

CAUTION

 

Do not operate the Generator, or any other appliance, before you have read and understood the 
instructions for use and keep near for ready use. 
 

California Proposition 65 

  WARNING 

Breathing diesel engine exhaust exposes you to chemicals known to the State of California to 
cause cancer and birth defects or other reproductive harm. 

 

Always start and operate the engine in a well ventilated area. 

 

If in an enclosed area, vent the exhaust to the outside. 

 

Do not modify or tamper with the exhaust system. 

 

Do not idle the engine except as necessary. 

For more information go to www.P65warnings.ca.gov/diesel. 

  WARNING 

Cancer and reproductive Harm- 
www.P65Warnings.ca.gov 

 

WARNING 

Batteries, battery posts, terminals and related accessories contain lead and lead compounds, and 
other chemicals known to the State of California to cause cancer and birth defects or other 
reproductive harm. WASH HANDS AFTER HANDLING. 

Summary of Contents for DGK15FL























































Reviews: