Simple Motors Kit 5 Assembly Instructions Manual Download | Manualshive

Page: 1 / 10

background image

Assembly instructions for kit #5

1

All rights reserved. 2001 Simple Motors, LLC

♦

www.simplemotor.com

♦

Assembly Instructions: Kit #5

1. Insert the T-pin into one of the caps.

2. Insert the rotor core into the same cap as shown below. Apply some pressure to push the

rotor core approximately 1/2" (10-12 mm) into the cap.

1
2
3
...
»

Summary of Contents for Kit 5











Reviews:

No comments

Related manuals for Kit 5

Brand: Danfoss Pages: 28

Brand: YOODA Pages: 6

Brand: Flux Pages: 28

E-8 DIESEL ENGINE

Brand: M.T.H. Pages: 36

FIFTY-FIVE - REV1 11-2007

Brand: NOVAK Pages: 2

Brand: ebm-papst Pages: 11

Brand: Hoval Pages: 12

High-Power RMS-PLUS 54/1706

Brand: Aerotech Pages: 2

RMS 98/10240 BLACK MAX

Brand: Aerotech Pages: 2

Brand: ABB Pages: 215

AG2210-LP Series

Brand: Beckhoff Pages: 35

Brand: Yanmar Pages: 182

Concept engines

Brand: RB Pages: 19

Brand: Mitsubishi Pages: 522

Brand: O.S. engine Pages: 11

Brand: JaxSon Pages: 40

Brand: DLE Pages: 4

Brand: Mitsubishi Heavy Industries Pages: 156

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands