background image

1

SimpliFire  •  SF-ALL48-BK, SF-ALL60-BK  •  2040-981 Rev. C  • 3/18

    

Model(s):

WARNING: To reduce risk of fire, electrical shock, or personal injury, read all instructions 

before using appliance. 

Owner’s Manual

Installation and Operation

DO NOT DISCARD THIS MANUAL

NOTICE

•  Leave this manual with 

party responsible for use 

and operation.

DO NO

T

DISCARD

•  Important operating 

and maintenance 

instructions included.

•  Read, understand and follow 

these instructions for safe 

installation and operation.

SF-ALL48-BK

SF-ALL60-BK

READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE, OR MAINTAIN 

THIS PRODUCT.

PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION.  FAILURE 

TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR 

PROPERTY DAMAGE. 

Please contact your SimpliFire dealer or customer/technical support 

(877-320-0730) with any questions or concerns. 

For the location of your nearest SimpliFire dealer, 

please visit www.hearthnhome.com.

Congratulations!

Congratulations on selecting a SimpliFire Electric Fireplace, an elegant and clean alternative to wood  & gas burning fireplaces. 

The SimpliFire electric fireplace you have selected is designed to provide the utmost in safety, reliability, and efficiency.

Printed in China  -  Copyright 2018

Allusion Series:

Summary of Contents for SF-ALL48-BK






















Reviews: