25
4
6
8
I. Disclaimers, Exclusions and Limitations of Liability
PLEASE READ AND NOTE SMARTPRO WARRANTY TERMS AND CONDITIONS as stated in
the warranty card. SmartPro warranty for its testers are subject to proper use by its user in accordance
with all the terms and conditions as started in the relevant user manual book and shall cover only
manufacturing defects.
Due to continuous product improvement, SmartPro reserves the right to revise all documents
including the right to make changes to the user manual without notice and without obligation
to notify any person of such revisions or changes. User s are advised to check SmartPro’s
website http://www.smartproinstrument .com from time to time.
SmartPro shall not be responsible for any damage or loss resulting from the use of this tester or
user manual, and under no circumstances shall SmartPro, its manufacturer or any of its subsidiaries,
licensors, distributors, resellers, servants and/or agents be liable for any direct or indirect damages,
resulting from the use of this tester.
II. About the SmartPro Finder I
The SmartPro Finder I is a pocket sized instrument that instantly verifies the authenticity of
diamonds based on their thermal properties. Diamonds, with their exceptional heat conductivity
properties, are unlike any other simulants, natural or synthetic, and are therefore not easily replicable.
The SmartPro Finder I has been subjected to thorough and extensive laboratory tests, and will
generally give a clear and reliable reading of the gemstone being tested under proper use. However,
you are advised to conduct further supporting tests.
As with all thermal testers in the market, the SmartPro Finder I is not able to differentiate between
natural diamonds and moissanite.
Include in your package:
a. SmartPro Finder I
b. User manual book
c. Warranty card
d. Protective carry case
e. Probe tip oxidation sheet
f. Neck strap
g. Metal stone tray
Fig. 2.1
23
All testers have been calibrated during the manufacturing process and no further adjustment or
user intervention to the tester is required.
Self-calibration should not be attempted. To minimize any risk associated, user should contact
SmartPro at customercare@smartproinstrument.com or its service center for assistance. In the
event that users require the manufacturer to re-calibrate the unit, the users will bear the associated
to/from freight cost for the shipping of unit to the service center.
Calibration
21
Gently rub the table of gemstone against the tissue/jewelry cloth and place the gemstone on the
center of the test pad
(Fig.1.8).
Fig. 1.8
20
Fig. 1.2
9
11
13
Composition
1. Retractable probe tip
2. Serrated Metal Part
3 “Ready” Indicator LED
4. “Low Battery” Indicator LED
5. “Metal” Indicator LED
6. “Simulant” Indicator LEDs
7. “Diamond” Indicator LED
8. ON/OFF Button Switch
9. Battery compartment
10. Neck Strap Attachment
11. Probe Protective Cap
f. Do not drop, knock, or shake the tester. Rough handling can break internal circuit boards and
fine mechanics.
g. Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the tester.
h. Do not paint the tester. Paint can clog the moving parts and prevent proper operation.
If the tester is not working properly, kindly contact our customer service at
customercare@smartproinstrument.com
SmartPro Instrument co.,ltd
249/40, Moo 9, J.S.P. Building
Bangbon 1 Rd., Bangbon
Bangkok 10150 Thailand
+66 (0) 2 899 2956-7
Attn: Customer Service Executive
Turning on
Remove the protective cover from the probe tip
(Fig. 1.2).
Prepare clean tissue / jewelry cloth. Carefully retrieve the gemstone with tweezers and place the
gemstone face down the table
(Fig.1.7).
Cleaning your gemstone prior to testing
Fig. 1.7
The gemstone should be clean and dry before testing. However, elaborate cleaning procedures
are not normally necessary
(Fig.1.6).
18
Recommended testing conditions
Fig. 1.6
Cleaning the probe tip
Please note that if the tester is being used for the first time, or if the tester has not been used for
a week, it is advisable to clean the probe tip using an oxidation removal sheet to attain consistent
and accurate reading.
b. Hold the probe pen with pen tip forming the right angle (90 degree) with an oxidation removal.
Gently move in a circular motion without retracting the tip
(Fig. 1.5)
.
16
a. Ensure the unit is switched off.
c. Repeat the same motion several times. The cleaning process is completed and tester is now
ready for use.
11
1
2
3
6
8
10
4
7
9
5
GENERATION AHEAD TECHNOLOGY
Thank you for choosing our SmartPro Finder I and taking time for the user manual book which will
enable you to understand your recent purchase better.
SmartPro Instrument also recommends that you register your warranty by sending the warranty
registration card to us or registering online at http://www.smartproinstrument.com
a. The probe and wire tip is extremely sensitive and should be handled with care. Please always
replace the protective cap. Caution should be taken so as not to damage the probe and wire tip.
b. Do not leave worn out batteries in the battery compartment as the batteries may corrode, leak
or damage the tester. Batteries should be removed when the tester is expected to be stored for
an extended period of time.
28
4. TAKING CARE of your SmartPro Finder I
20
Fig. 1.2
9
11
13
Composition
1. Retractable probe tip
2. Serrated Metal Part
3 “Ready” Indicator LED
4. “Low Battery” Indicator LED
5. “Metal” Indicator LED
6. “Simulant” Indicator LEDs
7. “Diamond” Indicator LED
8. ON/OFF Button Switch
9. Battery compartment
10. Neck Strap Attachment
11. Probe Protective Cap
f. Do not drop, knock, or shake the tester. Rough handling can break internal circuit boards and
fine mechanics.
g. Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the tester.
h. Do not paint the tester. Paint can clog the moving parts and prevent proper operation.
If the tester is not working properly, kindly contact our customer service at
customercare@smartproinstrument.com
SmartPro Instrument co.,ltd
249/40, Moo 9, J.S.P. Building
Bangbon 1 Rd., Bangbon
Bangkok 10150 Thailand
+66 (0) 2 899 2956-7
Attn: Customer Service Executive
Turning on
Remove the protective cover from the probe tip
(Fig. 1.2).
Prepare clean tissue / jewelry cloth. Carefully retrieve the gemstone with tweezers and place the
gemstone face down the table
(Fig.1.7).
Cleaning your gemstone prior to testing
Fig. 1.7
The gemstone should be clean and dry before testing. However, elaborate cleaning procedures
are not normally necessary
(Fig.1.6).
18
Recommended testing conditions
Fig. 1.6
Cleaning the probe tip
Please note that if the tester is being used for the first time, or if the tester has not been used for
a week, it is advisable to clean the probe tip using an oxidation removal sheet to attain consistent
and accurate reading.
b. Hold the probe pen with pen tip forming the right angle (90 degree) with an oxidation removal.
Gently move in a circular motion without retracting the tip
(Fig. 1.5)
.
16
a. Ensure the unit is switched off.
c. Repeat the same motion several times. The cleaning process is completed and tester is now
ready for use.
11
1
2
3
6
8
10
4
7
9
5
