background image

Table of Contents

1. IMPORTANT SAFETY INSTRUCTIONS ................................................................................. 4
2. COOKTOP MEASUREMENTS  ............................................................................................... 5
3. POSITIONING THE COOKTOP AND LOCATION REQUIREMENTS  .................................... 6

3.1 Gas supply requirements  ................................................................................................................................ 8
3.2 Electrical requirements .................................................................................................................................... 9

4. INSTALLING THE COOKTOP ............................................................................................... 11
5. CHECKING OPERATION ...................................................................................................... 14
6. WIRING DIAGRAMS  ............................................................................................................. 15

INSTRUCTIONS FOR THE INSTALLER:

 these are intended for the 

qualified engineer

 who is able to

install, commission and test the appliance

3

Summary of Contents for PU106
















Reviews: