background image

Contents 

 

 

1.

 

INSTRUCTIONS FOR SAFE AND PROPER USE _____________________ 22

 

2.

 

POSITIONING OF HOB _________________________________________ 24

 

3.

 

ELECTRICAL CONNECTION _____________________________________ 26

 

4.

 

GAS CONNECTION ____________________________________________ 27

 

5.

 

ADAPTATION TO DIFFERENT TYPES OF GAS______________________ 29

 

6.

 

FINAL OPERATIONS ___________________________________________ 32

 

7.

 

USING THE HOB ______________________________________________ 34

 

8.

 

CLEANING AND MAINTENANCE _________________________________ 36

 

 

 
 
 
 
 
 
 

 

 
 

 
 

 

 

THESE INSTRUCTIONS ARE VALID ONLY FOR END USER COUNTRIES WHOSE 
IDENTIFICATION SYMBOLS APPEAR ON THE COVER OF THIS MANUAL. 

 

 

 

 

INSTRUCTIONS FOR THE INSTALLER: these are for the 

qualified 

technician

 who must carry out a suitable check of the gas system, 

install the appliance, set it functioning and carry out an inspection test. 

 

 

INSTRUCTIONS FOR THE USER: these contain user advice, 
description of the commands and the correct procedures for cleaning 
and maintenance of the appliance. 

 

21

 

Summary of Contents for SE706S

















Reviews: