Sony Ericsson 802se Working Instruction, Electrical Download

Page: 1 / 13

Working Instruction, Electrical

Working Instruction, Electrical

Applicable for V800/ 802se

INDEX

LEAD FREE SOLDERING..........................................................................................................................................2

1.1

NTRODUCTION

.........................................................................................................................................................2

1.1.1

Environment.....................................................................................................................................................2

1.1.2

Soldering temperature .....................................................................................................................................3

BGA EQUIPMENT REFLOW PROFILES ...............................................................................................................5

2.1

EMPERATURE MEASUREMENT

................................................................................................................................5

2.1.1

Reflow Profiles ................................................................................................................................................6

REPLACEMENT OF PARTS......................................................................................................................................7

3.1

QUIPMENT

..............................................................................................................................................................7

3.2

NSTRUCTION HOW REPLACING PARTS

......................................................................................................................7

3.2.1

External Antenna Connector ...........................................................................................................................8

3.2.2

30 PIN BTB Female Connector, behind the System Connector.......................................................................8

3.2.3

30 PIN BTB Female Connector .......................................................................................................................9

3.2.4

50 PIN BTB Female Connector .......................................................................................................................9

3.2.5

Battery Connector..........................................................................................................................................10

3.2.6

USB Connector ..............................................................................................................................................10

3.2.7

MS Duo and SIM Reader...............................................................................................................................11

3.2.8

Hall Element ..................................................................................................................................................11

3.2.9

IrDa Module ..................................................................................................................................................12

3.2.10

Coax Connector.............................................................................................................................................12

REVISION HISTORY ................................................................................................................................................13

3/000 21-2/FEA 209544/88 C
Company Internal



Sony Ericsson Mobile Communications AB

Approved according to 000 21-LXE 107 42/1

Summary of Contents for 802se














Search results

Summary of Contents for 802se

Reviews:

Related manuals for 802se

Brands by name

Popular brands

Sony Ericsson 802se, Working Instruction, Electrical

Search results

Summary of Contents for 802se

Reviews:

Related manuals for 802se

Brands by name

Popular brands