background image

1

1

SERVICE MANUAL

US Model

Canadian Model

CDX-1200

E Model

CDX-3600

CDX-1200/3600

FM/AM COMPACT DISC PLAYER

• The tuner and CD sections have no adjustments.

Photo: CDX-3600

AUDIO POWER SPECIFICATIONS (US, Canadian model)

POWER OUTPUT AND TOTAL HARMONIC DISTORTION
18 watts per channel minimum continuous average power into
4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more
than 1% total harmonic distortion.

Other Specifications
CD player section

System

Compact disc digital audio
system

Signal-to-noise ratio

90 dB

Frequency response

10 – 20,000 Hz

Wow and flutter

Below measurable limit

Laser Diode Properties (US, Canadian model)

Material

GaAs + GaAlAs

Wavelength

785 – 815 nm (Typ. 800 nm)

Emission Duration

Continuous

Laser output power

Less than 0.5 mW*

This output is the value measured at a distance of

0.7 mm from the objective lens surface on the
Optical Pick-up Block.

Tuner section

FM

Tuning range

US, Canadian model: 87.5 – 107.9 MHz
E model:

FM tuning interval:
50 kHz/200 kHz switchable
87.5 – 108.0 MHz (at 50 kHz step)
87.5 – 107.9 MHz (at 200 kHz step)

Antenna terminal

External antenna connector

Intermediate frequency 10.7 MHz
Usable sensitivity

12 dBf

Selectivity

75 dB at 400 kHz

Signal-to-noise ratio

65 dB (stereo),
68 dB (mono)

Harmonic distortion at 1 kHz

0.7% (stereo),
0.5% (mono)

Separation

35 dB at 1 kHz

Frequency response

30 – 15,000 Hz

SPECIFICATIONS

AM

Tuning range

US, Canadian model: 530 – 1,710 kHz
E model:

AM tuning interval:
9 kHz/10 kHz switchable
531 – 1,602 kHz (at 9 kHz step)
530 – 1,710 kHz (at 10 kHz step)

Antenna terminal

External antenna connector

Intermediate frequency 10.7 MHz/450 kHz
Sensitivity

30 µV

Power amplifier section

Outputs

Speaker outputs
(sure seal connectors)

Speaker impedance

4 – 8 ohms

Maximum power output 45 W 

×

 4 (at 4 ohms)

– Continued on next page –

Model Name Using Similar Mechanism

CDX-1150, CDX-3700

CD Drive Mechanism Type

MG-310-153

Ver 1.1  2001. 05

Sony Corporation

e Vehicle Company

Shinagawa Tec Service Manual Production Group

9-870-052-12

2001E0400-1

© 2001. 5

Summary of Contents for CDX-1200 - Fm/am Compact Disc Player









































Reviews: