background image

– 1 –

Model Name Using Similar Mechanism

NEW

CD Drive Mechanism Type

MG-363X-121

Optical Pick-up Name

KSS-521A

SERVICE MANUAL

US Model

Canadian Model

E Model

CDX-4180

FM/AM COMPACT DISC PLAYER

MICROFILM

AUDIO POWER SPECIFICATIONS (US Model)

POWER OUTPUT AND TOTAL HARMONIC DISTORTION
17 watts per channel minimum continuous average power into
4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more than
1% total harmonic distortion.

Other Specifications
CD player section

System

Compact disc digital audio
system

Signal-to-noise ratio

90 dB

Frequency response

10 - 20,000 Hz

Wow and flutter

Below measurable limit

Laser Diode Properties

Material

GaAlAs

Wavelength

780 nm

Emission Duration

Continuous

Laser output power

Less than 44.6 

µ

W*

This output is the value measured at a distance

of 200 mm from the objective lens surface on
the Optical Pick- up Block.

Tuner section

FM

Tuning range

US, Canadian model:
87.5 - 107.9 MHz
E model:
FM tuning interval:
50 kHz/200 kHz switchable
87.5 - 108.0 MHz
(at 50 kHz step)
87.5 - 107.9 MHz
(at 200 kHz step)

Antenna terminal

External antenna connector

Intermediate frequency

10.7 MHz

Usable sensitivity

8 dBf

Selectivity

75 dB at 400 kHz

Signal-to-noise ratio

65 dB (stereo),
68 dB (mono)

Harmonic distortion at 1 kHz

0.5% (stereo),
0.3% (mono)

Separation

35 dB at 1 kHz

Frequency response

30 - 15,000 Hz

Capture ratio

2 dB

SPECIFICATIONS

AM

Tuning range

US, Canadian model:
530 - 1,710 kHz
E model:
AM tuning interval:
9 kHz/10 kHz switchable
531 - 1,602 kHz
(at 9 kHz step)
530 - 1,710 kHz
(at 10 kHz step)

Antenna terminal

External antenna connector

Intermediate frequency

10.71 MHz/450 kHz

Sensitivity

30 

µ

V

Power amplifier section

Outputs

Speaker outputs
(sure seal connectors)

Speaker impedance

4 - 8 ohms

Maximum power output

40 W 

×

 4 (at 4 ohms)

– Continued on next page –

Summary of Contents for CDX-4180 Instalation













































Reviews: