background image

SERVICE MANUAL

Sony Corporation

Audio&Video Business Group
Published by Sony Techno Create Corporation

CFD-S05

SPECIFICATIONS

CD RADIO CASSETTE-CORDER

9-889-821-01

2010C04-1

© 

2010.03

Australian Model

Singapore Model

Taiwan Model

Korea Model

Thai Model

Ver. 1.0  2010.03

CD player section

System
 

Compact disc digital audio system

Laser diode properties
 

Emission duration: Continuous

 

Laser output: Less than 44.6 

μ

W

 

(This output is the value measured at a distance of 

 

about 200 mm from the objective lens surface on the 

 

optical pick-up block with 7 mm aperture.)

Number of channels
 

2

Frequency response
 

20 Hz - 20,000 Hz +1/–2 dB

Wow and 

fl

 utter

 

Below measurable limit

Radio section

Frequency range
 

FM:  87.5 MHz - 108 MHz

 

Except SP model:

 

AM: 531 kHz - 1,602 kHz

 SP 

model:

 

AM: 531 kHz - 1,602 kHz (9 kHz step) 

 

 

530 kHz - 1,610 kHz (10 kHz step)

CD 
Section

Model Name Using Similar Mechanism

NEW

Optical Pick-up Name

DA11MMVGP

TC 
Section

Model Name Using Similar Mechanism

NEW

Tape Transport Mechanism Type

MF-S05V

IF (AUS, TH model)
 

FM: 128 kHz

 

AM: 45 kHz

Antennas
 FM: 

Telescopic 

antenna

 

AM: Built-in ferrite bar antenna

Cassette-corder section

Recording system
 

4-track 2 channel stereo

Fast winding time
 

Approx. 150 s (sec.) with Sony cassette C-60

Frequency response
 

TYPE I (normal): 80 Hz - 10,000 Hz

General

Speaker
 

Full range: 8 cm dia., 4 

Ω

, cone type (2)

Outputs
 

Headphones jack (stereo minijack):

 For 

16 

Ω

 - 32 

Ω

 impedance headphones

Input
 

AUDIO IN jack (stereo minijack)

– Continued on next page –

Summary of Contents for CFD-S05








Reviews: