background image

Ver 1.0  2001.02

CFM-S1

SERVICE MANUAL

RADIO CASSETTE-CORDER

SPECIFICATIONS

E Model

9-873-068-11

2001B0200-1

© 2001.2

Sony Corporation

Audio Entertainment Group

General Engineering Dept.

Model Name Using Similar Machanism

NEW

Tape Transport Mechanism Type

MF-M20-117

• Frequency range

FM: Saudi Arabia: 87.6 - 107 MHz
Other models: 87.6 - 108 MHz
MW: 530 - 1 605 kHz
SW1: 2.3 - 7 MHz
SW2: 7 - 22 MHz

• Aerials 

FM/SW: Telescopic aerial

MW: Built-in ferrite bar aerial

• Recording system 

2-track 1 channel mono

• Frequency response 

80 - 8 000 Hz

• Speaker 

Full range: 12 cm (4 

3

/

4

 inches) dia., 6

, cone

type (1)

• Outputs 

Earphones jack

For 8 

impedance earphones

• Maximum power output 

1.4 W

• Power requirements 

110 - 120, 220 - 240 V AC

selectable, 50/60 Hz
6 V DC, 4 R20 (size D) batteries

• Power consumption 

AC 8 W

• Battery life

FM recording: Sony R20P: approx. 18 h

Sony alkaline LR20: approx. 50 h

Tape playback: Sony R20P: approx. 12 h

Sony alkaline LR20: approx. 30 h

• Dimensions 

Approx. 287 

X

 147 

X

 110 mm (w/h/d)

(11 

3

/

8

 

X

 5 

7

/

8

 

X

 4 

4

/

8

 inches) (incl. projecting parts)

• Mass (incl. batteries) 

Approx. 2 kg (4 lb. 7 oz)

• Supplied accessory 

Mains lead (1)

Design and specifications are subject to change without
notice.

Summary of Contents for CFM-S1

























Reviews: