13-37P500D
CHAISE POUR DESSINATEURS
INSTRUCTIONS DE MONTAGE
© Office Star Products
Septembre
2010
WARNING
1. Use this product only one person at a time.
2. Do not use this chair unless all bolts screws and
knobs are securely tightened.
3. Check that all bolts screws and knobs are tight every
three months or as needed.
4. Dispose of packing material properly. Do not use
plastic cover as head covering. It may cause
suffocation.
5. Do not use chair as a stepladder.
6. Use this chair for its intended purpose only.
7. Use mild detergent only for cleaning.
LIMITED WARRANTY
SPACE® chairs are warranted* from the date of purchase against failure due to material and workmanship as follows:
• Lifetime on component parts including pneumatic cylinder, control mechanism, base and casters.
• 3 Years on upholstery fabric and foam against wear and deterioration.
*All warranties are limited to the original purchaser for normal commercial usage defined as a standard forty hour work week by
persons weighing 250 lbs. or less. This warranty will not cover labor, freight or damage from misuse, abuse, negligence, alteration,
accident, vandalism, rusting, acts of nature or any other event beyond the control of Office Star Products. The warranty does not
cover cosmetic damage that may result from normal use. Liability for incidental or consequential damages is excluded. The user
assumes all risk of injury resulting from use of this product. When usage is more than 40 hours per week, a five year warranty on
all parts applies. Fabric is warranted for one year. This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
To make a warranty claim, contact Parts Department via e-mail parts@officestar.net, by Fax 1-909-930-5629, or toll free parts
number 1-800-950-7262, Monday through Friday 8:00 a.m. - 5:00 p.m. Pacific Time. Provide model number and description of the
problem and obtain confirmation number. At it’s option Office Star Products will:
(a) Supply compatible components of current manufacture.
(b) Repair the customer’s component.
It is the customer’s responsibility to prepay freight on any components returned to the factory. Return freight on components
covered by warranty will be paid by Office Star Products.
13-37P500D
DRAFTING CHAIR
OPERATING INSTRUCTIONS
2
1
PIèCE
QTé
1.
Base . . . . . . . . . . . . . . . . . . . . 1
2.
Roulettes . . . . . . . . . . . . . . . . . 5
3.
Vérin pneumatique . . . . . . . . . 1
4.
Repose-pied . . . . . . . . . . . . . . 1
5.
Coussin du Siège . . . . . . . . . . 1
6.
Assemblage du dossier. . . . . . 1
7.
Vis . . . . . . . . . . . . . . . . . . . . . . 4
8.
Support du Dossier
(préinstallé) . . . . . . . . . . . . . . . . . 1
9.
Clé Allen . . . . . . . . . . . . . . . . . 1
Enlever toutes les pièces du carton, les organiser selon les numéros de pièce indiqués sur la liste et vérifier les quantités des pièces.
ÉtapE 1
Insérer les cinq roulettes (2) dans la base (1). Pousser fermement jusqu’à ce que les roulettes (2) s’encliquettent.
ÉtapE 2
Glisser le vérin pneumatique (3) à travers le repose-pied (4) et dans la base (1).
ÉtapE 3
Fixer le support du dossier (8) au coussin du siège (5) avec quatre vis (7).
RESSERRER COMpLÈtEMENt tOUtES LES VIS (7) aVEC La CLÉ aLLEN (9).
ÉtapE 4
Placer le siège assemblé sur le dessus du vérin pneumatique (3) et pousser vers le bas.
attENtION: aVaNt D’UtILISER LE FaUtEUIL, S’aSSURER D’aVOIR SERRÉ COMpLÈtEMENt tOUtES LES VIS.
.
FEATURES
•
PNEUMATIC SEAT HEIGHT
ADJUSTMENT
To raise seat remove pressure from seat and lift lever (1) up. To
lower seat height sit on chair and lift lever (1) up.
NOTE:
It is normal for chair to slightly lower under
body weight.
• FOOTRING HEIGHT ADJUSTMENT
To adjust footring height, loosen knob (2) adjust footring to
desired height, and tighten knob (2) completely to secure
footring into position.
éTAPE 1
éTAPE 2
éTAPE 3
éTAPE 4
2
X5
1
1
4
3
9
7
8
X4
5
6
3
