background image

BEFORE YOU START

Inside the box you will find your Enbrighten Spectrum LED Puck Lights with detached rings, 

remote, power supply, power cord, screws and mounting tape (pre-attached to pucks).

Organize Your Pucks: 

Carefully remove each puck from the box and lay it end to end in the 

desired installation sequence. The power cord should be closest to the nearest outlet. Be sure 

the installation surface is dry and will support the pucks. Use the cord management feature to 

adjust the length of each puck as necessary, starting from the puck nearest to the power supply. 

Once the pucks are aligned and spaced according your needs, wind up any excess cord into the 

pucks. 

IMPORTANT: 

Make sure cords are laying flat during installation. Lights are intended for 

indoor use only.

Cord Management Feature: 

To adjust 

the cord length, tighten (clockwise) or 

loosen (counterclockwise) the cords as 

needed by twisting the center of each 

puck. Note that the cord management 

feature works best when starting from 

the puck nearest to the power supply, 

then adjusting each successive puck.

INSTALLATION

Install the power supply and pucks using the attached mounting tape or the included screws for 

extra support.

STEP 1 - POWER SUPPLY

Using Mounting Tape

 1.  Remove the paper backing, align the power supply 

and firmly press to secure it to the surface for 30 

seconds. 

Using Screws with Mounting Tape

1.   Mark the screw locations of the two keyholes on the 

back of the power supply.  

2.  Secure the screws to the marked locations using a 

Phillips-head screwdriver.

3.  Align the keyholes with the screws, mount the power 

supply and fasten the screws as needed. 

NOTE: 

The power supply must be facing the appropriate direction for the power cord to 

reach the nearest outlet.

STEP 2 - PUCKS

Using Mounting Tape

 1.  Starting with the puck closest to the power supply, 

mark the locations of each puck. Make sure the cord 

is the appropriate length – it can be tightened after 

installation using the cord management feature.

2.  Each puck has two pieces of mounting tape. Peel off 

the paper backings, align the puck and firmly press it 

onto the surface for 30 seconds. 

3.  Repeat the process for each puck.

Using Screws with Mounting Tape

1.   Mount the pucks to the surface as described above.

2.  Gently extend the cord to its maximum length for each puck by twisting the center of 

the puck counterclockwise. This provides a clear line of sight to the keyholes and avoids 

potential damage caused by the screws.

3.  Use a 3/32in.* drill bit to drill holes in each keyhole location. 

4.  Use a Phillips-head screwdriver to insert the provided screws into the holes. Tighten screws 

as needed.

5.  Repeat the process for each puck, maintaining the same orientation for each one.

Refer to the manual or visit www.byjasco.com for limitations and restrictions on warranties and the product registration information.

WARNING:

 When using outdoor-use portable luminaires, basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and 

personal injury, including the following:

Ground Fault Circuit Interrupter (GFCI) protection is to be provided on the circuit(s) or outlet(s) to be used for the wet location portable luminaire. Receptacles are 

available having built-in GFCI protection and are able to be used for this measure of safety.

WARNING: 

Keep these bags away from babies and children. Do not use in cribs, beds, carriages, or playpens. The thin film may cling to nose and mouth and 

prevent breathing.

Warranty Information: 

This Jasco product is warrantied for three (3) years with a limited-lifetime replacement warranty on Enbrighten LED light source only. 

 

RISK OF ELECTRIC SHOCK

• RECEPTACLE OUTLETS USED FOR POWERING 

LANDSCAPE LIGHTS SHALL COMPLY WITH ALL 

NATIONAL AND LOCAL ELECTRICAL CODES. 

CONSULT LOCAL ELECTRICIAN IF UNSURE OF 

COMPLIANCE REQUIREMENTS.

• FOR USE ONLY ON GFCI PROTECTED CIRCUITS.

• DO NOT SUBMERSE.

• DO NOT USE AROUND AQUARIUMS. 

• LANDSCAPE LIGHTS ARE A WET-LOCATION 

PRODUCT AND HAVE NO SERVICEABLE PARTS.

• DO NOT USE WITH EXTENSION CORD, NEAR WATER 

OR WHERE WATER MAY ACCUMULATE.

• KEEP LAMPS AT LEAST 16 FEET FROM POOLS   

   AND SPAS.

• KEEP PLUGS AND RECEPTACLES DRY.

• AVOID DAMAGE TO THE CORDS AND LAMP 

ASSEMBLIES DURING INSTALLATION. PERIODICALLY 

INSPECT THE LANDSCAPE LIGHTS FOR PHYSICAL 

DAMAGE OR OTHER DAMAGE CAUSED BY OUTDOOR 

EXPOSURE TO THE ELEMENTS.

• REPLACE ANY DAMAGED LANDSCAPE 

LIGHTS.

• DO NOT INSTALL IN LOCATIONS WHERE 

LANDSCAPE LIGHTS CAN BE STEPPED ON.

• ENSURE LANDSCAPE LIGHTS ARE 

UNPLUGGED FROM POWER DURING 

INSTALLATION.

• CHILDREN SHOULD NOT PLAY WITH 

LANDSCAPE LIGHTS.

• UL RECOMMENDS TESTING GFCI CIRCUITS 

AND RECEPTACLES EVERY MONTH TO 

ENSURE PROPER OPERATION.

RISK OF FIRE

• LANDSCAPE LIGHTS ARE DESIGNED TO 

BE MOUNTED WITH THEIR INDIVIDUAL 

KEYHOLE MOUNTING FEATURE. DO 

NOT MOUNT LANDSCAPE LIGHTS USING 

THE MAIN ELECTRICAL CORD OR THE 

INDIVIDUAL DROP CORDS.

• NOT INTENDED FOR INSTALLATION IN 

CEILINGS, SOFFITS, CABINETS, ATTICS, OR 

OTHER ENCLOSED SPACES. 

MADE IN CHINA 
Distributed by Jasco Products Company LLC, 
10 E. Memorial Rd., Oklahoma City, OK 73114.
This Jasco product comes with a 3-year limited warranty.                             

Visit www.byjasco.com for warranty details.
Questions? Contact our U.S.-based Consumer Care at 1-855-698-8324 

between 7AM-8PM, M-F,  Central Time.
Patents pending  |  www.enbrightenme.com

Important — please read:

WARNING

40090 40091 40092 

Version 1

08/27/20

STEP 3 - RINGS

Each puck has a ring that fits over the lens to protect the light and secure the cord.

Attaching the Rings

 1.  Feed the cords through the small openings on either side of the ring. 

2.  Twist the ring counterclockwise until it snaps securely into place.

3.  To remove the ring, twist clockwise.

STEP 4 - CONNECT TO POWER

Once the power supply and pucks are mounted, plug in the power cord to the nearest outlet. 

OPERATION

Your 

Enbrighten Spectrum LED Puck Lights are paired with the included remote control. However, if you 

want to pair additional puck sets or remotes, follow these steps: Within five seconds of plugging in the 

pucks, press and hold the ON/OFF button on the remote. The lights blink twice to indicate they are paired 

with the remote.

ON/OFF: 

Turns the pucks ON and OFF

Favorite: 

Press when on your preferred color or mode to recall later. Only 

one setting can be saved.

Modes: 

Cycles through 10 color modes

Color Select: 

Cycles through 15 color options

White Select: 

Cycles through six white light options

Bright /-: 

Adjusts the brightness level with full-range dimming

NOTE: 

To unpair the remote, press and hold the WHITE SELECT button. 

Mounting the Remote: 

You can also mount the RF remote to a wall to operate as a light switch. Remove 

the remote’s body from the housing to reveal two mounting keyholes inside. Mark the keyhole locations 

using a pencil, then drill holes using a 3/64in.** drill bit. Insert the screws leaving approximately 1/8in. from 

the surface. Seat the remote’s housing onto the screws and fasten as needed. Place the remote into the 

housing.

NOTE: 

Your remote also comes with a magnetic strip on its back, allowing you to easily mount the remote 

on most metal surfaces.

READ IT 

OR

 WATCH IT

Read instructions or watch easy-to-follow video. 

Scan QR code or visit https://byjasco.com/44090i

on/off

favorite

modes

color

select

bright

-

white

select

bright

select

Pucks

3

6

9

Model No.

UCL/44/3/39/12/120

UCL/44/6/78/24/120

UCL/44/9/117/36/120

Location Use

Indoor

Input Watt, Max.

11.2

22.9

35.1

on/off

favorite

modes

color

select

bright

-

white

select

bright

select

Mounting

tape

Mounting

tape

Keyhole for 

mounting 

with screws

Keyhole for 

mounting 

with screws

Mounting

tape

Mounting

tape

Mounting

tape

Keyhole for 

mounting with screws

Keyhole for 

mounting with screws

Tighten

Loosen

1.

2.

3.

Summary of Contents for enbrighten UCL/44/3/39/12/120

Page 1: ...D LOCAL ELECTRICAL CODES CONSULT LOCAL ELECTRICIAN IF UNSURE OF COMPLIANCE REQUIREMENTS FOR USE ONLY ON GFCI PROTECTED CIRCUITS DO NOT SUBMERSE DO NOT USE AROUND AQUARIUMS LANDSCAPE LIGHTS ARE A WET LOCATION PRODUCT AND HAVE NO SERVICEABLE PARTS DO NOT USE WITH EXTENSION CORD NEAR WATER OR WHERE WATER MAY ACCUMULATE KEEP LAMPS AT LEAST 16 FEET FROM POOLS AND SPAS KEEP PLUGS AND RECEPTACLES DRY AVO...

Page 2: ...switch opens to reveal program buttons For addtional stakes and accessories visit www enbrightenme com or call 1 800 654 8483 myTouchSmart In Wall Digital Timer Model 414311 myTouchSmart Sunsmart In Wall Digital Timer Model 33861 myTouchSmart Outdoor Indoor Wifi Smart Plug Model 39845 Multiple lengths and styles available now at www enbrightenme com Drill Hole Drill Hole Simplify your enbrighten e...

Page 3: ...le la fuente de alimentación y los discos con la cinta de montar adherida o con los tornillos provistos si desea soporte adicional PASO 1 FUENTE DE ALIMENTACIÓN Uso de la cinta de montar 1 Retire el papel protector alinee la fuente de alimentación y presione con firmeza durante 30 segundos para fijarla a la superficie Uso de los tornillos con la cinta de montar 1 Marque las ubicaciones para los to...

Page 4: ...nte con wifi para exterior interior Modelo 39845 En www enbrightenme com encontrará varias longitudes y estilos disponibles Perforar orificio Perforar orificio Simplifique su experiencia con las bombillas Enbrighten automatizando los momentos de encendido y apagado Recomendamos los siguientes modelos disponibles en comercios seleccionados o en www enbrightenme com WARM VINTAGE LIGHT 2200K LINKABLE...

Reviews: